672452

Titan TTK587GDO Manual

47
Zoom out
Zoom in
Previous page
1/58
Next page
5. Maintenance
WARNING! Always switch the product off, let the product cool down and disconnect
the spark plug connector before performing inspection, maintenance and cleaning
work!
WARNING! Only perform repairs and maintenance work according to these
instructions! All further works must be performed by a qualified specialist!
WARNING! Wear safety gloves when working on the attachment heads and close to
it! Use appropriate tools to remove debris, e.g. a brush or wooden stick! Never use
your bare hands!
Keep the product clean. Remove debris from it after each use and before storage.
Regular and proper cleaning will help ensure safe use and prolong the life of the product.
Inspect the product before each use for worn and damaged parts. Do not operate it if you find
broken and worn parts.
GENERAL CLEANING
NOTE: Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfectants
to clean this product as they might be harmful to its surfaces.
1. Clean the product with a slightly damp cloth and mild soap. Use a brush for areas that are
hard to reach.
2. In particular clean the air vents after every use with a cloth and brush.
3. Remove stubborn dirt with high pressure air (max. 3 bar).
4. Check for worn or damaged parts. Replace worn parts as necessary or contact an
authorised service centre for repair before using the product again.
Blade (Brush Cutter)
1. Keep the cutting blade (B5) clean and free of debris. Remove clippings.
2. Keep the cutting blade (B5) sharp to retain a good cutting performance. Replace a worn or
damaged cutting blade with a new one of the same type.
Trimmer Head
1. Keep the trimmer head (B11) clean and free of debris. Remove trimmings.
2. If the line is used up the spool must either be replaced by one of the same type or the
trimming line (B12) must be refilled.
3. To refill the trimming line lay the product on a flat stable surface with its trimmer head facing
upwards.
4. Rotate the backing flange until one of the notches is aligned with the hole in the gear head.
5. Insert the spindle lock rod (E3) into the hole to lock the spindle.
6. Remove the trimmer head (B11) by unscrewing clockwise. (See Fig. 34a)
Fig. 34a
47
25CC PETROL MULTI TOOL TTK587GDO
E3
… 47 …


Need help? Post your question in this forum.

Forumrules
1

Forum

titan-ttk587gdo

Reset search

  • WE BOUGHT A 587GDO and have not got a bolt/nut with the trimmer - do you know if the model has been modified since 2017 or can the nut be purchased ?
    Thanks Submitted on 27-7-2023 at 17:57

    Reply Report abuse

  • This product is not fit for purpose
    Why it’s there a clear instruction to extent the strummer line and head removal Submitted on 17-5-2022 at 15:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Titan TTK587GDO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Titan TTK587GDO in the language / languages: English as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info