475000
13
Zoom out
Zoom in
Previous page
1/23
Next page
P10
MAIN MENU
7.1.1 Satellite Settings
Use this menu to change the settings for a given satellite and to configure the parameters
for the used antenna Use
pq to highlight Satellite and tu to set the satellite you wish to
change the settings for. To see a list with all available satellites, press OK when the highlight
is on Satellite. Use
pq to highlight Transponder and tu to set the desired transponder.
Signal bars indicating signal quality and strength can be found on the bottom of the screen.
These bars show the signal conditions for the chosen satellite and transponder. You can now
adjust the following settings: LNB type, LO Frequency, LNB power, Band (22kHz), Switch Type,
Switch Input, Antenna Mode and Antenna Position. Once all settings are made, press EXIT
to get to the previous menu or use
pq to highlight Go To and tu to select Auto Scan or
Manual Scan to advance to Auto Scan or Manual Scan.
A confirmation banner will now be displayed. Press OK to confirm the made changes or EXIT
to discard.
7.1.2 Auto Scan
Use this menu to perform an automatic channel search on one or more satellites.
On the left of the screen, a list with satellites is displayed. Use
pq to highlight the satellite(s)
you wish to scan and press OK to mark the highlighted satellite. Press OK again to unmark a
marked satellite.
NOTE:
you can mark multiple satellites. Auto Scan will search all marked satellites for
available channels.
Now select the desired scanning options on the right of the screen. Use u pq to highlight
and OK to set an option.
Scan Mode: All: scan all channels, Free: scan Free-To-Air channels only,
Scrambled: scan scrambled channels only.
Service Type: All: scan TV and Radio channels, TV scan TV channels only, Radio:
scan radio channels only.
Network Search: Disabled: no network search, Enabled: network search will
be performed.
Once all settings are made, press the GREEN button on the remote control to start the scan or
EXIT to quit without scanning.
All newly found channels will be stored at the end of the channel list.
TIP:
Network Search: If Disabled is selected, the receiver will search only for channels available
from the preset transponder list of the selected satellite. If it is set to Enabled, the receiver will perform an
additional search for channels from the NIT table (NIT= Network Identification Table). Use this option to receive
new launched channels from the selected satellite.
7.1.3 Manual Scan
Use this menu to scan a single transponder only.
The following can be set: Satellite, Transponder, Frequency, Polarisation, Symbolrate, Scan
Mode, Service Type and Network search. Use
pq to move the highlight to the chosen setting
and
tu to change its value. Once all settings set correct, press the GREEN button to start
scanning or EXIT to quit. All newly found channels will be stored at the end of the channel list.
NOTE:
If you want to scan for a specific channel only, press YELLOW in the Manual Scan menu
to make settings for a PID search. Scan mode, Service type and Network search will then be replaced by
settings for Video PID, Audio PID and PCR PID. For information on PID values, please visit websites like:
www.lyngsat.com or www.kingofsat.net
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson TSR600CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson TSR600CI in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson TSR600CI

Thomson TSR600CI User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info