699585
11
Zoom out
Zoom in
Previous page
1/22
Next page
English
7
By connecting your receiver to the latest digital ampliers or home theatre systems with HDMI
connections, you will enjoy the best possible sound quality and multi-channel audio (depending on
broadcast), up to Dolby Digital Plus. Connect the HDMI output of the receiver to an input of your
amplier, and then connect the HDMI output of the amplier to your TV set. Select the correct input
on your amplier to watch and listen to programmes.
3.6 Connecting to Ethernet
Fig. 7
Connect a CAT5 cable (or higher quality) to the LAN (RJ45) connector of the unit and the other end
to an existing switch, router or modem. The default setting is Auto (DHCP) for automatically obtaining
IPs and DNS. Select DHCP O in Menu> System>Network Setting>IP setting to enter your own
settings if required. When setting up manually, you need to provide a unique IP address, Netmask,
Gateway and DNS for your receiver. Refer to the manual of your router or modem to setup properly.
signalling will give momentary status of connection, like cable unplugged, local network or internet.
3.7 Connecting a USB storage device
Fig. 8
NOTE: We recommend the use of a hard disk drive USB 2.0 or higher for
recording and play back of TV events.
For proper functioning of Timeshift and recording functions, a fast USB device (such as a hard
disk drive) is needed. Interrupted playback or a distorted picture during playback or Timeshift are
indications for a low device speed. STRONG cannot guarantee proper functioning of recording and or
Timeshift functions with all USB devices.
4.0 STARTING UP FOR THE FIRST TIME
If you use your receiver for the rst time, the Installation Guide menu appears. Use pq to move the
highlight to the setting you wish to change and use t u to change values. Start by selecting your
On-Screen Language (OSD) using t u. Once you have selected your language, press q to move
the highlight to Country. Select your country using t u.
Other options are:
Antenna Power: Set to On if you use an active antenna. When set to On, a 5 Volt power will
be present on the RF IN connector of the receiver. Select O for passive
antennas.
Scan mode: Select All to store scrambled and free to air channels or select FTA to store
only Free-To-Air channels. Note: Scrambled channels you cannot watch with
this receiver.
Once all settings are made, move the highlight to Channel Search and press OK to start scanning.
The receiver will now search for all available channels. Once scanning is nished, the receiver switches
to viewing mode.
NOTE: Selecting the wrong country may result in a disorderly channel list, and
missing of channels.
TIP: In case the Installation Guide menu does not appear after switching on
the receiver the rst time, reset the receiver to factory settings by pressing
the MENU button and selecting Restore Factory Default in submenu
System. (Default PIN 1234)
5.0 QUICK GUIDE TO USING YOUR RECEIVER
We at STRONG understand that you can't wait to enjoy your new high denition digital terrestrial
receiver. The following quick guide will make you familiar with the basic operation of this device. We
do, however, advice you to read the full manual to get the best performance from your receiver.
To turn your receiver ON or to Standby, use the q button on the remote control.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THT709 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THT709 in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson THT709

Thomson THT709 User Manual - French - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info