658794
18
Zoom out
Zoom in
Previous page
1/30
Next page
P18
7. MAIN MENU
7.1.3 System Settings
Use the System Settings menu to configure settings for language, audio, video, look and feel of your receiver.
Choose a setting with pq and press OK to list the possibilities or use tu to change the value of the
highlighted setting. Please also read the displayed instructions for each screen carefully. They will help you to
adjust the settings correctly and easily.
Language: Here you can change the language for the On-Screen-Display, use tu to select your
preferred language. It affects the menu language of your receiver so all menus and
messages will be displayed in the chosen language.
Video Setting: Select the connection to your TV set. Either Scart or HDMI can be selected via tu.
Press OK at the used connection to open the settings for it. For details, see chapter
7.1.3.1 HDMI or 7.1.3.2 SCART.
Audio Output: Here you can adjust the settings for your digital audio output. Press tu to choose
between BitStream and PCM. If a device that can decode Dolby® Digital is connected,
use the setting BitStream. If this is not possible, use PCM.
Audio language: Press OK to open the setting. The most important audio languages are displayed. For
details, see chapter 7.1.3.3 Select Audio Language.
Subtitle Setting Press OK to open this setting. For details, see chapter 7.1.3.4 Select Subtitle Language
Start up channel In this menu you can select your start up channel. Select Last watched if you want to
start with the last viewed channel when the receiver was switched off. To switch on
with a specific channel, select Fixed Channel by pressing tu. Press OK and OK again to
continue. Press pq or P+/P to scroll in the list and confirm your selection with OK.
Banner display time: Defines the time for displaying the information banner. Press tu to choose between
1 sec ~ 20 sec.
OSD transparency: Defines the transparency of menus and banner. Press tu to choose between 25%,
50%, 75% and fifty-fifty.
When all settings have been made, press
to leave the System Settings menu. When returning to viewing
mode the receiver informs with a message that it saves your settings.
7.1.3.1 HDMI
In this submenu you can set following parameters:
TV Ratio 16:9 or 4:3, depending on the kind of your TV set.
Conversion Letterbox, PanScan or Combined, to choose the preferred picture format.
Video Output Only selectable for Scart
Resolution 576p, 720p, 1080i or 1080p, to adjust the optimum resolution your TV set supports.
HDCP ON or OFF, please see the note below.
NOTE: HDCP (High Definition Content Protection) is set to ON per default as nowadays all TV sets with an
HDMI connector support HDCP. If you have problems with the HDMI connection you can use the
Scart setting to deactivate HDCP, which will allow watching via HDMI without problems. Consider
that movies which are broadcasted with an extra content protection might not be shown when
HDCP is set to OFF.
NOTE: If you configure an HDMI resolution which isn’t supported by your TV, there is no problem because if
you press no button the receiver will switch to the last used resolution after ~ 10 sec automatically.
However, if you can see the displayed message, then confirm the selected resolution by pressing OK.
7.1.3.2 SCART
In this submenu you can set following parameters:
TV Ratio 16:9 or 4:3, depending on the kind of your TV set.
Conversion Letterbox, PanScan or Combined, to choose the preferred picture format.
Video Output RGB or CVBS, depending on what your TV set supports, but for Scart we recommend RGB.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS813 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS813 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info