480544
15
Zoom out
Zoom in
Previous page
1/27
Next page
P10
MAIN MENU
7.1 Installation
This menu allows you to change satellite settings and to search for channels. Further you can
adjust important settings for your receiver. It consists of the following sub-menus: Antenna
Setup, Channel Search, System Settings, Parental Lock and Factory Reset. Choose the
desired sub menu with
p/q and press OK to advance.
7.1.1 Antenna Setup
Use this menu to change or add the settings for an already installed or new satellite and to
configure its parameters. In the Type line you can adjust if you’re using a DiSEqC switch or not
by using
t/u to change. If your setup differs you can adjust DiSEqC OFF or use default setting
DiSEqC 1.0.
Is DiSEqC OFF used you will only be able to setup one satellite. Press OK to open the settings
for this connection.
For the usage with DiSEqC 1.0 you can enter the same parameters for up to 4 satellite positions.
Edit LNB
Satellite: Press OK to open the list of available satellites and chose the desired one
with
p/q or PG+/-.
LNB Type: Choose the desired LNB Type via the
t/u buttons if you are not using an
“Universal” LNB.
LNB Low Freq.: This shows the value for the appropriate LNB Type used and you can only
adjust for “Normal” LNB.
LNB High Freq.: This shows the value for the appropriate LNB Type used and you can only
adjust for “Normal” LNB.
22KHz Tone: This setting for AUTO should not be changed, only in case it is necessary
for your LNB type.
LNB Power: Here you can change the LNB power via
t/u in case it is necessary.
Transponder: Press OK to open the list of available transponders for the chosen
satellite, in order to check your reception or align the antenna.
After all settings are adjusted following to your system requirements, choose Save with
p/q or
Cancel to discard changes and press OK. The receiver will return to the selection screen and
you can continue.
In case you want to delete a desired satellite press the GREEN button. If you want to delete all
satellites that have been setup use the YELLOW button to do so. Once all settings are made,
press EXIT/SORTIE to change to the previous menu.
7.1.2 Channel Search
Use this menu to perform an automatic, network or transponder channel search or to search on
all satellites that have been setup. Use
p/q to highlight the desired item and t/u to change
settings. Below the settings you can find the search methode selection.
Antenna: Here you can change the antenna port via
t/u in case you have
configured more than one satellite.
Satellite: Here you will see the according satellite which is assigned to the antenna
in above, you can only see the satellite(s) which has/have been setup in
Antenna Setup menu before.
Transponder list: By using
t/u you can change between the transponders referring to the
selected satellite, you can also press OK to list up and select with
p/q
or PG+/-. Afterwards press OK to choose. Use RED to Edit TP, with
GREEN you can Delete TP and with BLUE you can enter data for a new
TP Add TP.
Scan Mode: Here you can decide for which channels you want to scan: Either scan
all channels FTA & $, for Free-To Air only FTA or use CA to scan for
scrambled channels only.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS 812 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS 812 in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info