699744

Thomson ROC1128PHI Manual

6
Zoom out
Zoom in
Previous page
1/78
Next page
4
5. Press the [MUTE] and [VOL-] buttons to
save all learnt functions and to exit the
learning mode.

While replacing the batteries, the remote control
will keep the functions of the learned keys.
    
     
1. Press and hold [MUTE] and [VOL+] keys
for 5seconds until the LED will be lit.
5
2. Enter the code [9] [8] [1], the LED will
ash 2times and then remain on.
3. Press and release the desired key at the
replacement remote control which you
want to clear the learned command. If the
LED ashes 3times, the learned command
has been cleared successfully.
     
1. Press and hold [MUTE] and [VOL+] keys for
5seconds until the LED will be lit.
5
2. Enter the code [9] [8] [2], the LED will ash
2times and then remain on.
3. Press and release the [OK] key at the
replacement remote control. If the LED
ashes 3times, allcommands have been
cleared successfully.
  
This remote control is equipped with an
 .Thus you could reduce the
functionality of the remote control to its basic
functions. It avoids that the TV Settings are
changed by mistake.
During the   you still could use
following keys:
Switch the TV On or Off
–/
+
Change the volume
Mute the TV
–/
+
Change the program
 Numeric keys for program selection/
direct page selection Teletext
 Teletext ON/OFF
Use to select avariety of on-screen
options
 Show the Electronic Program Guide
(if supported by the TV)
Select signal source
Exit Menu
 Shift to TV
   
1. Press and hold [MUTE] and [VOL+] keys for
5seconds until the LED will be lit.
5
2. Enter the code [9] [7] [0], the LED will ash
two times and then remain on.
3. Press and release the [OK] key,ifLED ash
3times, you have entered the 
 successfully.
   
1. Press and hold [MUTE] and [VOL+]
for 5seconds until the LED will be lit.
5
2. Enter the code [9] [7] [0], the LED will ash
two times and then remain on.
3. Press and release the [EXIT] key,ifLED
ash 3times, you have exit the 
.

While the   is activated only
the keys mentioned in chapter 7will work.
If one of these keys is pressed the LED will
be lit until the key is released. If one key is
pressed during the normal mode, the LED
will ash.
 
•Donot mix new and used batteries for
powering the Universal Remote Control, as
old batteries tend to leak and may cause
power drain.
•Donot use corrosive or abrasive cleansers on
your Universal Remote Control.
•Keep the Universal Remote Control dust free
by wiping it with asoft, dry cloth.
 
Q. My Universal Remote Control does not
work at all!
A. Check your TV. If the TV main switch is
turned off, your Remote cannot operate
your TV.
A. Check whether your batteries are inserted
properly and are in the correct +/- position.
A. Check whether you have pressed the
corresponding device mode key for your
device.
A. If the batteries are low, replace the
batteries.
Q. My TV responds only to some of the
commands.
A. Try other codes until most keys work
properly.
Q. Some keys of the Remote Control do not
work anymore?
A. Maybe the   had been
activated. Deactivate the   as
explained in chapter 7.2.
  
The manufacturer assumes no liability and
provides no warranty for damage resulting
from improper installation/mounting, improper
use of the product or from failure to observe
the operating instructions and/or safety notes.
GB
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC1128PHI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC1128PHI in the language / languages: All languages as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info