699744

Thomson ROC1128PHI Manual

5
Zoom out
Zoom in
Previous page
1/78
Next page
3
GB
2. Enter the three codes from code Iist.
When the code input is nished, the
LED will turn off.
3. Please try to use the remote control.
lf it doesn‘t work well, please try other
codes: [002], [003], [004] ...

lf the code is invalid, the LED ashes twice
and then lights up permanently.Toexit the
setup, please press [MUTE].
  
1. Press and hold the key [MUTE] and
[POWER] until the LED will be lit, then
release keys.
2. Press the key [CH+]. Each time you
press, the remote will search once.
When the code changes, you can test
if [POWER], [VOL+],[MENU],[0-9] keys
work well. If ok ,please press [MUTE] to
save the code and exit.
3. lf it doesn‘t work well, repeat the fast
search by pressing [CH+].
  
Use the following method to nd out which
code is currently set:
1. Press and hold [MUTE], then press
[POWER] until the LED will be lit, then
release keys.
2. Input [9].[9].[0] with number keys. The
LED will ash twice and goes off.
3. Press the number key 1for the 1st digit
of the code. The LED will start to ash.
Count the LED ashes. The number of
ashes resemble the code‘s rst digit.
Repeat this procedurefor the 2nd and
3rddigit of the code:
2nd digit -> enter 2->count LED
ashes
3rddigit -> enter 3->count LED ashes
lf code number is [0] the LED will not
ash.
    
Due to too many Remote Control models, we
only Iist some of them below.
lf your remote control is similar to the drawing,
the replacement remote can control your TV
(Page 74).
    
Press and hold the [RETURN] and [0] buttons for
about 5seconds until the status LED flashes three
times and then goes out. The remote control is
now successfully reset to the factory settings.

All keys with learnt codes or all copied keys,
as well as all remote control settings will
be deleted.
  
This remote control is equipped with alearning
function. Thus, you could learn functions of
your original remote to this remote control.
    
•The batteries in the two remote controls
have to be in good condition. Replace them
if necessary.
•Place the remote controls with the infrared
diodes so that they point towards each
other.
•Wherenecessary adjust the height of both
remotes so that infrared diodes areproperly
aligned.
•The distance between the remote controls
should be about 3cm.

•Donot move the remote controls during
the learning procedure.
•E
nsur
et
hat
the
ro
om
is
not
lit
by
uor
escents
tubes
or
low
ener
gy
consumption
lamps
since
such
light
sour
ces
could
interfer
ew
ith
the
copying.
•The 2remotecontrols must be at least
1meter away from any light source.
•During learning mode, if no key is
selected for morethan 15 seconds, the
learning mode will exit automatically or
if no other remote signal is received.
•Each function key will hold only one
command. Anew command to be learned
will automatically replace the previous one.
   
1. Press and hold the [MUTE] and [VOL+]
keys for approx. 5seconds until the LED
will be lit.
5
2. Enter the code [9] [8] [0], the LED will ash
2times and then remain on.
3. The remote control is now ready to learn
new commands.
   
1. Press and release the desired key on the
original remote control which you want the
command to be learned. The LED at your
replacement remote will ash to conrm
that the information has been received.
2. Then press and release the target key on
the remote control you want learned.
3. If the LED ashes 3times and then remain
on, the command has been learned
successfully.
4. Repeat these steps to learn other key
functions.
ca. 3cm
ORIGINAL
ROC1128PHI
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC1128PHI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC1128PHI in the language / languages: All languages as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info