699742

Thomson ROC1128LG Manual

6
Zoom out
Zoom in
Previous page
1/78
Next page
4
GB
3. If the LED ashes 3times and then remain
on, the command has been learned
successfully.
4. Repeat these steps to learn other key
functions.
5. Press the [MUTE] and [VOL-] buttons to
save all learnt functions and to exit the
learning mode.
Note
While replacing the batteries, the remote control
will keep the functions of the learned keys.
6.4 CLEARING OF LEARNED KEYS
6.4.1 CLEARING OF ONE LEARNED KEY
1. Press and hold [MUTE] and [VOL+] keys
for 5seconds until the LED will be lit.
5
2. Enter the code [9] [8] [1], the LED will
ash 2times and then remain on.
3. Press and release the desired key at the
replacement remote control which you
want to clear the learned command. If the
LED ashes 3times, the learned command
has been cleared successfully.
6.4.2 CLEARING OF ALL LEARNED KEYS
1. Press and hold [MUTE] and [VOL+] keys
for 5seconds until the LED will be lit.
5
2. Enter the code [9] [8] [2], the LED will ash
2times and then remain on.
3. Press and release the [OK] key at the
replacement remote control. If the LED
ashes 3times, all commands have been
cleared successfully.
7. SIMPLE Mode
This remote control is equipped with an
SIMPLE Mode.Thus you could reduce the
functionality of the remote control to its basic
functions. It avoids that the TV Settings are
changed by mistake.
During the SIMPLE Mode you still could use
following keys:
Power TV ON /OFF
Volume UP/DOWN
Turn your TV sound ON/OFF
Channel UP/DOWN
0-9 Numeric keys 0–9toenter channel
numbers
Teletext On
Use to select avariety of on screen
options
GUIDE Show the Electronic Program Guide
(if supported by the TV)
Input Signal source
Exit TV Menu
Switch TV or Radio mode
7.1 Enter SIMPLE Mode
1. Press and hold [MUTE] and [VOL+] keys for
5seconds until the LED will be lit.
5
2. Enter the code [9] [7] [0], the LED will ash
two times and then remain on.
3. Press and release the [OK] key,ifLED ash
3times, you have entered the SIMPLE
Mode successfully
7.2 Exit SIMPLE Mode
1. Press and hold [MUTE] and [VOL+]
for 5seconds until the LED will be lit.
5
2. Enter the code [9] [7] [0], the LED will ash
two times and then remain on.
3. Press and release the [EXIT] key,ifLED
ash 3times, you have exit the SIMPLE
Mode.
Note
While the SIMPLE Mode is activated only
the keys mentioned in chapter 7will work.
If one of these keys is pressed the LED will
be lit until the key is released. If one key is
pressed during the normal mode, the LED
will ash.
8. Maintenance
•Donot mix new and used batteries for
powering the Universal Remote Control, as
old batteries tend to leak and may cause
power drain.
•Donot use corrosive or abrasive cleansers on
your Universal Remote Control.
•Keep the Universal Remote Control dust free
by wiping it with asoft, dry cloth.
9. Troubleshooting
Q. My Universal Remote Control does not
work at all!
A. Check your TV. If the TV main switch is
turned off, your Remote cannot operate
your TV.
A. Check whether your batteries are inserted
properly and are in the correct +/- position.
A. If the batteries are low, replace the
batteries.
Q. My TV responds only to some of the
commands.
A. Try other codes until most keys work
properly.
Q. Some keys of the Remote Control do not
work anymore?
A. Maybe the SIMPLE Mode had been
activated. Deactivate the SIMPLE Mode as
explained in chapter 7.2.
TEXT
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC1128LG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC1128LG in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info