Manual Thomson ROC1128LG (page 5 of 78) (All languages)

699742

Zoom out

Zoom in

1/78

1. Press and hold the key [MUTE] and

[POWER] until the LED will be lit,

then release keys.

2. Enter the three codes from code Iist.

When the code input is nished, the

LED will turn off.

3. Please try to use the remote control.

lf it doesn‘t work well, please try other

codes: [002], [003], [004] ...

Note

lf the code is invalid, the LED ashes twice

and then lights up permanently.Toexit the

setup, please press [MUTE].

5.2 FAST SEARCH

1. Press and hold the key [MUTE] and

[POWER] until the LED will be lit, then

release keys.

2. Press the key [CH+]. Each time you

press, the remote will search once.

When the code changes, you can test

if [POWER], [VOL+],[MENU],[0-9] keys

work well. If ok ,please press [MUTE] to

save the code and exit.

3. lf it doesn‘t work well, repeat the fast

search by pressing [CH+].

5.3 CODE INQUIRY

Use the following method to nd out which

code is currently set:

1. Press and hold [MUTE], then press

[POWER] until the LED will be lit, then

release keys.

2. Input [9].[9].[0] with number keys. The

LED will ash twice and goes off.

3. Press the number key 1for the 1st digit

of the code. The LED will start to ash.

Count the LED ashes. The number of

ashes resemble the code‘s rst digit.

Repeat this procedurefor the 2nd and

3rddigit of the code:

2nd digit -> enter 2->count LED

ashes

3rddigit -> enter 3->count LED ashes

lf code number is [0] the LED will not

ash.

5.4 Compatible Remote Control Model

Due to too many Remote Control models, we

only Iist some of them below.

lf your remote control is similar to the drawing,

the replacement remote can control your TV

(Page 74).

5.5 Resetting to factory settings

Press and hold the [BACK] and [0] buttons for

about 5seconds until the status LED flashes three

times and then goes out. The remote control is

now successfully reset to the factory settings.

Note

All keys with learnt codes or all copied keys,

as well as all remote control settings will

be deleted.

6. LEARN MODE

This remote control is equipped with alearning

function. Thus, you could learn functions of

your original remote to this remote control.

6.1 BEFORE STARTING LEARN MODE

•The batteries in the two remote controls

have to be in good condition. Replace them

if necessary.

•Place the remote controls with the infrared

diodes so that they point towards each other.

•Wherenecessary adjust the height of both

remotes so that infrared diodes areproperly

aligned.

•The distance between the remote controls

should be about 3cm.

Note

•Donot move the remote controls during

the learning procedure.

•E

nsur

hat

the

not

lit

uor

escents

tubes

low

ener

consumption

lamps

since

such

light

sour

ces

could

interfer

ith

the

copying.

•The 2remotecontrols must be at least

1meter away from any light source.

•During learning mode, if no key is

selected for morethan 15 seconds, the

learning mode will exit automatically or

if no other remote signal is received.

•Each function key will hold only one

command. Anew command to be learned

will automatically replace the previous one.

6.2 ENTER LEARN MODE

1. Press and hold the [MUTE] and [VOL+]

keys for approx. 5seconds until the LED

will be lit.

2. Enter the code [9] [8] [0], the LED will ash

2times and then remain on.

3. The remote control is now ready to learn

new commands.

6.3 LEARNING OF KEYS

1. Press and release the desired key on the

original remote control which you want the

command to be learned. The LED at your

replacement remote will ash to conrm

that the information has been received.

2. Then press and release the target key on

the remote control you want learned.

ca. 3cm

ORIGINAL

ROC1128LG

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC1128LG in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC1128LG Manual

Product: