576934
6
Zoom out
Zoom in
Previous page
1/29
Next page
14. Bars should be glued for rigidity (see diagram 11). Reposition the rear wall
and fix in position. The wall should be standing between 16 and 40 mm in
front of aperture.
15. Trim the cut (from the door aperture) to fit the door panel according to
template 4A or 4B (make sure you use the right template!). Make sure the
decoration lines are lined up with the wall (see diagram 12).
16. Fill the groove of the door outer with sealant. Position the panel in the door
outer (see diagram 13), and then push the door inner into the door outer.
17. Fill the groove of the frame outer to be placed in the opening with sealant
(see diagram 14), place the complete door against the outside wall of the
vehicle and fasten the door with 9 sheet-metal screws (4.2x12.5mm).
18. Mount the frame inner from the inside onto the door (see diagram 15).
19. If the kicking plate was removed before installation, then reassemble it, fix it
with clips (3x) to the front bottom of the toilet.
20. In case of using wall brackets, fix these brackets to the rear wall using screws
(see diagram 16).
21. Install the shower tray first in case of new designed or adjusted shower tray.
22. Before positioning the toilet, the electrical connection has to be made first.
C-402 Red wire is the positive wire
Black wire is the negative wire
If the toilet is going to be connected to a pressure system:
C-403 Red wire is the positive wire
Black wire is the negative wire Drawing 1A
Purple wire is not required - do not connect
Grey wire is not required - do not connect
If the toilet is going to be connected to a non-pressure system:
Red wire is the positive wire
Black wire is the negative wire Drawing 1B
Purple wire is positive input (12V DC) - connect to electric supply
Grey wire is positive output - connect to positive side of pump
Remark: connect the negative wire to a common negative
23. Position the toilet against rear wall and aperture wall (see diagram 17).
24. Before installing the toilet, the C-403 has to be connected to the water supply
system. Connect the water hose of the cassette (inside diameter 3/8” =
10mm) to the water hose of the water supply with a hose adapter. Fix the
hoses to the adapter with a clamp (see diagram 1 8).
25. If using wall brackets, place the toilet over these brackets (see diagram 19).
26. Position the unit (through the door aperture from the outside) to the outside
wall, by gripping it at the pockets in the base. Secure the back panel of the
toilet to the bathroom rear wall with 4 screws (4 x 30mm) underneath the
toilet seat.
27. Install a cover strip if necessary (see diagram 20).
28. Add a run of transparent sealing mastic from the outside between door and
toilet (see diagram 21). The toilet is now installed.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thetford C-402C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thetford C-402C in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 1.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thetford C-402C

Thetford C-402C User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info