576934
5
Zoom out
Zoom in
Previous page
1/29
Next page
HELPFUL TIPS
Drawings for making templates are included for easy installation.
Assembly instructions should be followed step by step.
The following tools are required:
- (el.) drill and drill-bit 3 and 8 mm
- an electric jig saw
- Philips screwdriver number 2
- ruler
- (felt) pen
- safety glasses
- butyl compound waterproof sealant
The cut out of the outer wall will be used as door panel, therefore do NOT cut
or drill any other holes than noted in this installation manual!
INSTALLATION INSTRUCTIONS
The toilet should be fixed to a vertical back wall. When a back wall is unavailable,
one will have to be installed (see point 6, 8, 14).
1. Take the toilet out of the box.
2. Remove plastic bag with parts out of the bowl. Included should be the
“instructions for use” and a holding tank cap.
3. Read “instructions for use” to get familiar with part names. Remove cassette
waste tank by lifting the tank locking clip at the pour-out spout (see diagram
2).
4. Remove all loose parts from toilet fluid storage compartment.
5. Remove shower tray if it will not allow fitting of toilet and modify to suit if
possible.
6. Position the toilet unit at the chosen place against outside wall and lift the
cover to check for vertical clearance. If new vertical wall needs to be erected,
put some scribe lines for the position of the back wall. Erect the rear wall
temporarily into position. Check if the wall is vertical and square with the
outside vehicle wall. Remove the toilet.
7. Position template 1 into the corner of the rear wall/outer vehicle wall and the
surface where the toilet will stand on. In case of carpet, take compressing into
consideration (see diagram 7).
8. Drill two holes 3 mm through the vehicle wall from the inside. Positions are
indicated on template 1. Remove the template.
9. Position template 2 on the outside, using two screws in drilled holes. Outer
dimensions template 2 is for checking 20 mm (distance from trimming, body
extrusions and, or wheel arch to aperture) (see diagram 8).
10. Replace template 2 with 3 and draw a line with a felt pen around template 3
to mark the cutting line for the door frame aperture (see diagram 9).
11. Remove template 3 and put tape for protection against scratching at the end
and outside of the cutting line. Insert the jig saw blade according to diagram
10.
12. Make the cut out with a jig saw. Be sure to cut perpendicular to the outer wall
(see diagram 10).
13. Prepare 4 wooden bars to be inserted into outer wall as reinforcement for
locating outer frame.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thetford C-402C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thetford C-402C in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 1.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thetford C-402C

Thetford C-402C User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info