648194
79
Zoom out
Zoom in
Previous page
1/94
Next page
User’s manual User’s manual
GB
77
9.4 - Connect the radiator
The radiator must be powered at 230V
50 Hz.
The radiator power supply must be
connected directly to the network behind
the omni-pole breaking device with a
contact opening distance of at least
3 mm without an intermediate switch
(clock, mechanical and static relay,
ambience thermostat, etc).
The connection to the mains power supply will be made using a 3-wire cable (Brown =
Phase, Blue = Neutral, Black = Pilot wire) through a connection box. The connection box
must be installed at least 25 cm above the oor in wet rooms like kitchens, the bathrooms.
The installation must be provided with a circuit breaker type protection device.
Connection to the earth is prohibited. Do not connect the pilot wire (black) to the earth.
The manufacturer, his after sales service or a similar qualied person must replace the
power supply cable if it is damaged, so that the work can be done safely.
The power supply cable must be put back into position and fixed with the plastic
flange to hold the thermostat in position. There is a risk of electrical danger if this
operation is not respected.
If the pilot or piloted radiator is protected by a 30mA differential protection device (e.g.
bathroom), then the power supply to the pilot wire connected onto this differential switch
will have to be protected.
Pilot wire connection test
You can connect the pilot wire if your house is tted with a programming unit, or a power
manager.
In this case, make the following checks to verify that programming orders are transmitted
correctly:
Orders
Received
No
current
230V for 3s 230V for 7s 230V
-115V
négative
+115V
positive
Signal to be
transmitted
Mode
Obtained
COMFORT
COMFORT
-1°C
COMFORT
-2°C
ECO
FROST
FREE
SWITCH
HEATING
OF /
LOAD
SHEDDING
As regards the programming by pilot wire or current carrier, the frost-free or relief orders
take priority.
The time for switching from the comfort mode to the Eco mode takes about 12 seconds.
9.5 - Lock the radiator on its wall-mounting frame
- Place the radiator on wall-mounting frame S as
shown on the diagram.
- Bring the radiator to the wall-mounting frame and
then lift it (arrows 1 and 2).
- Insert the wall-mounting frame tabs in the radiator
holes and then lower the radiator (arrow 3).
- Lock by turning the 2 V screws by half a turn and
your radiator is xed.
10 - GETTING USED
10.1 - The Control box
OK
Equilibrium
ECO
0h 6h 12h 18h 24h
5
2
4
8
6
7
3
1
Screen Buttons and Buttons and
OK - Heating On/off
Settings
Smart Control function
Equilibrium
Equilibrium
Consumption indicator
10.1.1 - Description of the box screen
ECO
0h 6h 12h 18h 24h
Smart Control function
Data line
Display program
Heating light indicator
Display set T°C
Modes
Locked controls
Equateur2_1880-1585_interieur.indd 77 18/06/12 06:22
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermor Equateur 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermor Equateur 2 in the language / languages: English, French as an attachment in your email.

The manual is 6,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info