532670
7
Zoom out
Zoom in
Previous page
1/34
Next page
Pag.7
3.8 Setting the flame size / Extinguishing the fire
* After the burner is ignited, the flame size will automatically move into the maximum setting.
* Press (small) to reduce the flame size and turn off the burner.
(Extinguishing the fire: STAND BY”). (Pressing the key for a short time gradually reduces the flame).
* Press (large) to increase the flame. (Pressing the key for a short time gradually increases the flame.)
3.9 Switching the unit off
* Press
to reduce the flame size and turn the burner off (“STAND BY”).
Then press OFF to turn the entire unit off, including the pilot flame.
* If the unit is not used for an extended period of time, you can turn the “O I” switch, on the gas control
block, into the “O” position, in order to save battery life.
* In this case, it is also recommended you close the gas shut-off cock in the supply line.
Breakdowns:
* If the signals from the manual transmitter are not received adequately by the receiver, this may be caused
by:
1. Flat batteries: replace the batteries.
2. An electronic problem: can be solved by pressing the “RESET” key on the receiver.
3. Contact your fitter if the unit regularly turns off.
Important: If, for whatever reason, the pilot light extinguishes, you must wait 5 minutes before igniting
the pilot light again.
3.10 Inserting and replacing the batteries
* The batteries of the manual transmitter and receiver have a life span of approximately one year. The use of
alkaline batteries is recommended.
* The batteries need to be replaced when the following occur:
1. Manual transmitter: BATT appears on the display.
2. Receiver: long sound signals can be heard during the ignition.
1. Manual transmitter:
* Open the small lid on the back.
* Carefully remove the 9V block battery and loosen the battery from the contact holder. Do not pull the
wires!
* Connect the new battery and place it back into the transmitter. Close the lid.
2. Receiver:
* Carefully remove the entire receiver from the holder.
* Slide the small lid open.
* Remove the batteries from the battery holder.
* Place 4 new 1.5V batteries (type LR6 or AA) in the battery holder in the indicated manner. The spring
always needs to be against the minus (-) pole of the battery.
* Close the lid and place the receiver back into the holder.
Incorrect placing of the batteries can irreparably damage the electronics or power.
Only replace the batteries when the unit is completely turned off.
Important
Only remove batteries using non-metallic tools.
Removing batteries with a metal object may damage the electronic control permanently.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline Quadro 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline Quadro 46 in the language / languages: English as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thermocet Trimline Quadro 46

Thermocet Trimline Quadro 46 Installation Guide - English - 85 pages

Thermocet Trimline Quadro 46 User Manual - English - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - German - 85 pages

Thermocet Trimline Quadro 46 User Manual - German - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - Dutch - 85 pages

Thermocet Trimline Quadro 46 User Manual - Dutch - 85 pages

Thermocet Trimline Quadro 46 Usermanual and installation guide - Dutch - 34 pages

Thermocet Trimline Quadro 46 Installation Guide - Danish - 85 pages

Thermocet Trimline Quadro 46 User Manual - Danish - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - French - 85 pages

Thermocet Trimline Quadro 46 User Manual - French - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - Spanish - 85 pages

Thermocet Trimline Quadro 46 User Manual - Spanish - 85 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info