532670
6
Zoom out
Zoom in
Previous page
1/34
Next page
Pag.6
3.6 Controls (Remote Control)
Igniting the fire
* Open the gas shut-off cock that has been installed in the gas pipe to the unit.
* Press theO I” switch, on the gas control block, in the “I” position.
* Turn the operating button on the gas control block, into the ON position.
* Simultaneously press OFF and (large) on the manual transmitter. A short sound signal will confirm
commencement.
Short sound signals will then follow until the pilot flame and main burner are ignited.
After the main burner is ignited, the flame size will automatically move into the maximum setting.
3.7 Possible error messages
* Long sound signals during the ignition: Receiver batteries are almost empty. (After this signal occurs, the
unit can be switched on approximately another 10x).
* 5 seconds of continuous sound signal: Error message. For example: one of the cables is not connected, the
O I” switch is not in the “I” position.
* 5x short sound signal: Ignition of the pilot flame and main burner is unsuccessful.
Possible cause: air in the pilot pipes.
Important
If the pilot light extinguishes, one should wait at least 5 minutes
before repeating the aforementioned steps.
Piezo connector
(With manual
operation)
Control button
Motor button
(in the maximum setting)
Microswitch
O I” switch
8-pole receiver cable
connection
Gas control block (Operating button in ON-position
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline Quadro 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline Quadro 46 in the language / languages: English as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thermocet Trimline Quadro 46

Thermocet Trimline Quadro 46 Installation Guide - English - 85 pages

Thermocet Trimline Quadro 46 User Manual - English - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - German - 85 pages

Thermocet Trimline Quadro 46 User Manual - German - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - Dutch - 85 pages

Thermocet Trimline Quadro 46 User Manual - Dutch - 85 pages

Thermocet Trimline Quadro 46 Usermanual and installation guide - Dutch - 34 pages

Thermocet Trimline Quadro 46 Installation Guide - Danish - 85 pages

Thermocet Trimline Quadro 46 User Manual - Danish - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - French - 85 pages

Thermocet Trimline Quadro 46 User Manual - French - 85 pages

Thermocet Trimline Quadro 46 Installation Guide - Spanish - 85 pages

Thermocet Trimline Quadro 46 User Manual - Spanish - 85 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info