607245

Thermocet Trimline 85 R - 1050 Manual

27
Zoom out
Zoom in
Previous page
1/43
Next page
Page 27
11.4 Installation and assembly of the CC flue system with accessories.
See Chapter 7 Concentric flue system on Page 14 and the "Concentric paths Table" on page 31.
* It is also possible to install the fire using fireproof plate 50 mm Superisol .
(See installation example on p.36 Fig. A, B and C)
* After installing the fireplace and the various connections have been made and also checked for leaks and
proper operation of equipment required, the logs should be placed next.
11.5 Fitting the ceramic log inset (see page 39 to 41)
Attention! Before placing ceramic log inset, you
have to change the the 2 aeration brackets under
the double burner. This all for an optimal view of
the fire at gas category G25 20-25mbar.(I2E, I2E + I2H,)
Method:
* Remove decorative plate and burner out of the burning chamber.
* Unscrew the Aeration bracket with two holes Ø 9 mm from the
burner.
* Place the Aeration bracket for G25 with two holes Ø 5 mm
* Place screws back in place.
* Place burner and decorations back in place.
* The burner pressure, and the injector do not need to be altered.
Please note: when installing the log set and the various glowing materials and accessories, the following
must be taken into account:
A: Keep the opening between the burner and the burner plate free of glowing material
B: Ceramic materials should not come into contact with the cord of the window fixture.
Remove this if necessary. The window may otherwise be damaged.
Mix the glowing material (lava granules) and the “fusilli” (spiral-shaped ceramic material) and spread them
evenly over the burner and the burner plate so that they are just covered. Glowing embers can be placed here
and there as decoration.
* There should be no glowing material in or on the pilot burner.
NOTE: the remaining material can be discarded. The use of too much glowing material can adversely affect
the combustion process.
* Place the ceramic wood blocks in the correct order as shown on Page 39 and 40.
* Place the logs carefully. Other location can seriously affect the flames or malfunction of the burn process
(explode)
* Before replacing the windows make sure if there must be a restriction plate to be placed or not.
See page 14 and "Table of concentric path" on page 31
* If there is a restriction is required for your situation, remove the baffle plate by unscrewing it from the front
of the plate after the plate backwards and then out to be taken. Now install the restrictor plate with two
screws and replace the baffle plate.
* Now place the two windows in reverse order as described on page 26.
Incorrectly installed ceramic wood blocks and glowing material may have a significant influence on the
fire image and the burning effect.
11.6 Fitting the optional pebble set (see page 41)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Place a row of medium-sized and large pebbles at the front of the burner plate
* Fill the burner tray with small and medium-sized pebbles from the front to the rear. Place the pebbles as
closely as possible to each other on the burner tray.
* Fill the rear of the burner plate with medium-sized and large pebbles.
MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED!
* Before replacing the window make sure if there must be a restriction plate to be placed or not.
See page 14 and "Table of concentric path" on page 31
* If there is a restriction is required for your situation, remove the baffle plate by unscrewing it from the front of
the plate after the plate backwards and then out to be taken. Now install the restrictor plate with two screws
and replace the baffle plate.
* Now place the two windows in reverse order as described on page 26.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline 85 R - 1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 85 R - 1050 in the language / languages: English as an attachment in your email.

The manual is 4,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thermocet Trimline 85 R - 1050

Thermocet Trimline 85 R - 1050 Usermanual and installation guide - Dutch - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info