607243

Thermocet Trimline 10038 Panorama-Corner Manual

13
Zoom out
Zoom in
Previous page
1/49
Next page
Page.13
7.3 Installation instructions regarding existing flues.
Instructions
The flue gas exhaust system falls within category C91 and must be built in accordance with national rules and
regulations and the instructions of the manufacturer, as specified in the documentation and installation
instructions.
This means, among other things, that the chimney pass-through must not be smaller than 150 mm round / square,
but no larger than 200 mm, and not ventilated by grilles etc. In the case of larger chimney pass-throughs, a
flexible hose of around 150 mm may possibly be used in combination with a flexible hose of around 100 mm, as
described below. For other situations, you should consult your supplier / manufacturer.
7.4 Parts
Check all parts for damage before commencing the installation. You will require the following parts for
converting a brickwork duct to a concentric duct connecting to a CC duct system (see page 14 fig. A):
1. Fireplace
2. Concentric duct 100-150 or 130-200 mm
3. Mounting plate inside, square 300 mm
4. Adapter, single-wall
5. Parkers (4 x)
6. Flexible hose, stainless steel 316 L, single-wall and round 100 /107
7. Hose bracket, stainless steel
8. Existing brickwork duct
9. Mounting plate / connecting piece on the roof, square 300 mm
10. Clamping strap
11. Roof pass-through, standard
Note: The renovation/sanitation set consists of parts 3, 4, 5, 7, and 9.
7.5 Installation (See page 14, figure A)
· Guide the flexible hose (6) through the existing duct (8).
· Attach the adapter (4) to the bottom of the flexible hose and secure this in place using 2 parkers (5).
· The mounting plate (3) is adjustable, slide / fix it on to the outer pipe and then mount it against the ceiling
(airtight).
· Shorten the flexible hose to approximately 50 mm above the chimney coping plate.
· Attach the mounting plate / connecting piece to the flexible hose on the roof (9), clamp it with a hose bracket
(7) and secure it in place using a parker (5).
· Attach the mounting plate / connecting piece to the chimney coping watertight on the roof (9) using silicone
sealant and stainless steel screws.
· Install the roof pass-through (11) and secure it in place using the supplied clamping strap (10).
· Position the unit (1) in accordance with the instructions of the unit manufacturer.
· Always install a minimum of 1 metre of concentric duct type CC/US 100-150 (2), or 130-200 mm with
reduction to 100-150 mm.
7.6. Cleaning and maintenance.
The unit must be cleaned and checked every year by your dealer. The Concentric flue system must be cleaned
every 2 years.
Carry out the checks in accordance with the inspection list on page 22.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline 10038 Panorama-Corner at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 10038 Panorama-Corner in the language / languages: English as an attachment in your email.

The manual is 4,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info