49509
2
Zoom out
Zoom in
Previous page
1/5
Next page
7.0 Selection programs P1, P2, P3 and P4
S1 S2
For the 2 key dimmer
One brief keystroke on the (bright) key switches on the light on.
One brief keystroke on the (dark) key switches on the light off.
One long keystroke on the (bright) key slowly increases brightness
to 100 %.
If the key is previously released, the value that has been reached is main
tained.
A further long keystroke increases brightness to 100 %.
One long keystroke on the (dark) key reduces the brightness to
10 % and/or the minimum value (if a value has been previously set).
Program P2
Program P2 corresponds to P1, except
when switched on. In this case, the light
does not switch to 100% brightness but
to the last brightness value prior to
switching off.
After the 1st short keystroke, the (bright)
key (with 2-keys dimmer) dims to the set
value and then down to 100 % brightness
after the 2nd keystroke.
“Teaching-in” a brightness value (upper reduction value for P3)
The upper reduction value can be “taught-in“ here (in position P2), see
Section 8.
Hall
Living area
Child 1
Kitchen
Child 2
Parents
floor
Dark
For the 1 key dimmer
One brief keystroke switches on the light
to 100 %.
Pressing it again switches the light
off again.
A long keystroke dims the light.
The light is dimmed up to 100%, for exam-
ple, for as long as the key is depressed.
It is then dimmed down again. The entire process is repeated until the key
is released again.
“Teaching-in” a brightness value (minimum value in P1 to P4)
The smallest value to which the dimmer is to be set can be “taught in“ (in
P1 position), see Section 8.
4 programs P1 to P4 can be selected using the program selector switch.
Program P1
Program P1 is the standard dimming program with the following sequences:
Channel 1
Channel 2
Channel 1
Channel 2
Diode module
Light
Program P3 (stairwell function with continuous light)
Program P3 behaves like an automatic stairwell light and is identical on 1
and 2 switch dimmers. P3 runs as follows:
One keystroke switches the light on
to 100 %.
The light is maintained at 100% for 1, 2, 4
or 8 min. periods (see “Teaching-in” the
stairwell light time, Section 8).
The value is then reduced to between 40 %
and 80 %. This value is maintained for 40 sec.
P3 then switches to 30 % or the pro
grammed minimum value.
This value is maintained for 10 sec.
Program P3 switches off.
If during this process the key is pressed briefly, the
“stairwell light function” starts from the beginning.
If during this process the key is pressed for longer than 3 sec., the pro-
gram switches to continuous light (100%) and confirmation is signaled
by flashing briefly.
Channel 1
Channel 2
6.0 Connection and installation
Connecting the inputs
Input I 1 acts on output D1.
Input I 2 acts on output D2.
Input S 1 acts on output D1.
Input S 2 acts on output D2.
Important: In 1-channel operation,I 2 and S 2 do not function.
Input LS can trigger 3 independent light settings.
Ensure correct polarity!
Make the 2-wire connection between the COM interfaces.
Do not connect the inputs in parallel.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Theben Luxor 405 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Theben Luxor 405 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Theben Luxor 405

Theben Luxor 405 User Manual - German - 5 pages

Theben Luxor 405 User Manual - Dutch - 5 pages

Theben Luxor 405 User Manual - French - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info