606551
24
Zoom out
Zoom in
Previous page
1/41
Next page
Continuous drive actuator CHEOPS drive
theben
As of: Jul-11 (Subject to change without notice) Page 24 of 41
4.2 Calibration strategies
2 additional calibration strategies from software V61 / V61 (drive).
The aim is to enable adjustment to maximum number of different valves.
The selection of the calibration strategy is made via input in the "Strategy for valve
identification" parameter
4.2.1 Strategy 1, standard
The valve is measured during a calibration run (e.g. after reset) and the "valve open" and
"valve closed" positions are stored. The calibration run is performed twice after download and
the resulting values compared for plausibility. The calibration run is performed until two
successive matching value pairs have been measured. These values are then stored and the
positions used for future runs. The measured values are compared with the stored values
during the calibration run so that the process is only performed once for plausibility.
4.2.2 Strategy 2, Automatic (only for devices from software version 63/
61 drive)
With this option, only the "Open" valve position is calculated during the calibration run. In
order to close the valve, the actuator pushes out the tappet until the set force is exerted on the
valve. The following closing forces are available:
Closing force for
Closing force
Standard valves
approx. 100 N
Valves with high spring tension
approx. 120 N
It is always recommended to use the "normal valve" setting first as this is completely
sufficient for most valves.
The "Valve with high spring tension" setting should only be tried if you cannot close the
valve. This enables the current consumption to be increased to 15 mA during the pressing of
the rubber seal.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Theben CHEOPS drive KNX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Theben CHEOPS drive KNX in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Theben CHEOPS drive KNX

Theben CHEOPS drive KNX User Manual - English - 1 pages

Theben CHEOPS drive KNX User Manual - German - 42 pages

Theben CHEOPS drive KNX User Manual - German - 1 pages

Theben CHEOPS drive KNX User Manual - Dutch - 43 pages

Theben CHEOPS drive KNX User Manual - French - 43 pages

Theben CHEOPS drive KNX User Manual - French - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info