636713
10
Zoom out
Zoom in
Previous page
1/11
Next page
10
Change of aerator roll
Replacing aerator cylinder (illustration 10-12):
10. Disconnect the power cord
11. Tilt the machine around on the side.
12. Unscrew the two screws on the underside of the
hosing using an allen key.
13. Lift the aerator cylinder at an angle and pull away
from driver shaft.
14. Remove the bracket from the earator cylinder
15. Push the bracket on to the new cylinder
16. Push new aerator cylinder on to the driver shaft.
17. Fix the bracket to the underside of the housing
and tight the 2 screws using the allen key without
tightening too much.
18. The scarfier cylinder is fitted in the same way.
Inspect the cylinders for damage, cracks or excessive
rust or corrosion. Replace is necessary.
Art. no. 428573 - complete aerator cylinder (blades)
Art. no. 428579 - complete scarifier cylinder (springs)
Art. no. 428575 - individual springs
Danger!
The aerator/scarifier cylinders can cause injuries!
Prior to inspecting faults, unplug the power cord and
wait until the cylinder has stopped rotating completely.
Wear working gloves when inspecting faults.
Storage and maintenance
Maintain your lawn raker
Check all bolts, screws, nuts and deck. Always make
sure that the cylinders are in good condition. Replace if
necessary.
Disconnect the power cord, and clean the cutting deck
from grass/moss after every use.
Store the lawn raker in a dry and clean room.
The engine must be completely cooled off
before storing indoor or covered !
Before long time storage, dip a cloth in oil and lubricate
the metal parts to prevent rust. Protect the machine
from frost by covering it with e.g. a blanket.
Foldable handlebar (illustration 9)
Loosen the handle bar fasterning knob and , the
handle bar could be Z type folded.
Technical specifications
Model
MPC1500
Motor
1500W / 230V ~ 50 Hz
Rotations per minut
4000 rpm (no-load)
Working width
32 cm
Working depth
-12 ~ +5 mm
Grass catcher
50 l.
Weight
15 kg
Noise level
94 dB(A)
Vibration
3.05 m/s
2
Protection class
IPX4
Warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are
NOT covered by the warranty.
Wearing parts, which are NOT covered for more than
12 months:
Blades/springs
Cables
Belts
Fuses
Switches
Printed circuit boards (PCB)
The warranty does NOT cover damages/faults
caused by:
Lack of service and maintenance
Structural changes
Exposure to unusual external conditions
Damages to the bodywork, deck, handles etc.
If the machine has been improperly used or
overloaded
Use of unoriginal spare parts.
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is
determined in each case by an authorized service
center.
Your receipt is your warranty note, why it should
always be kept safe.
Remember: The purchase of spare parts as well as
any request for warranty repair, model number, year
and serial number should always be informed.
It can be found on the CE-label on the machine.
*We reserve the right to change the conditions and
accept no liability for any misprints.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas MPC 1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas MPC 1500 in the language / languages: English, Danish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info