636713

Texas MPC 1500 Manual

9
Zoom out
Zoom in
Previous page
1/11
Next page
9
Mounting
Mounting of handlebar (illustration 2-4):
1. Attach the cable hock ① to the lower handle ②
2. Insert the lower handle ② into the bracket block
③. Then insert the knob ④ from outside through
the hole in the lower handle ② and attach the bolt
to the lawn raker.
3. Insert the two locking bolts ⑧ from inside through
the hole in the upper handle ⑦ and secure to the
middle handle ⑥ with two wing nuts ⑤.
4. Insert the two locking bolts ⑧ from inside through
the hole in the lower handle ② and secure to the
middle handle ⑥ with two wing nuts ⑤.
Mounting of grass catcher (illustration 5-6)
1. Push the grass catcher handle ⑨ into the slots in
the grass catcher upper part ⑩ until it clicks
securely into positon.
2. Press the grass catchers right part ⑾ into the grass
catcher left part ⑿. Ensure all clips are correctly in
place.
3. Starting at the rear of the grassbox, press the grass
catcher upper part ⑩ into the grass catcher lower
part. Ensure all clips are correctly locate.
4. Fitting fully assembled grass catcher to lawn raker:
Lift the safety guard ⒀
Make sure the discharge chute is clean and
free from debris
Fit the fully assembled grass catcher onto
location points at the rear of the deck as
illustrated
Let safety guard ⒀ fall onto the top of the
grass catcher to lock it in place.
Use without grass catcher (illustration 6)
Note: The lawn raker can be used without the grass
catcher attached. Make sure that the safety guard ⒀
goes down and block the discharge chute.
Working depth adjustment
Adjusting the working depth (illustration 8)
The aerator/scarifier cylinder has variable depth
adjustment position: -12 ~ +5 mm.
When you want to move the aerator to outdoor, you
should always rotate the adjustment button ① to the
“high” position to protect the aerator cylinder.
The aerator/scarifier cylinder is subject to wear in use
due to the way in which it works . The more intensively
the machine is used, the greater the wear on the
blades/springs.
Hard or very dry ground accelerates wear, as does
excessive use of the machine.
Depending on the ground hardness, e.g. after a long
dry perioid, where the ground/lawn is hard, it is
recommended to start working in one of the higher
depth positions to avoid damage on the machine.
After check the work result, the working depth can be
increased step-by-step until the wanted result is
achieved. Never begin working in lowest postion!
Operation
Never use the machine if the grass is longer than
75 mm and remember to empty the grass catcher
regulary. Always start use the machine with in one
of the higher working depth positions.
Use an extention cord in good quality.
Minimum diameter of conductor: 1.5 mm
2
(0-20 m)
Starting (illustration 7)
3. Press and hold the safety button ①. Squeeze the
switch lever ② towards the handle
4. Release the safety button
Stopping (illustration 7)
2. Release the switch lever ②
Make sure the blade stoppes rotating
before switching “on” again !
Do not rapidly switch on and off !
IMPORTANT: Do not continue use the lawn raker,
when the grass catcher is already full. This can
overload the motor, as high heat can occur.
Make sure to check and empty the graas catcher often.
It can quickly become full, if there is a lot of moss in the
lawn or the working depth is set to a deep position.
Working pattern (illustration 13)
It will be useful to start working from at a point close to
the power supply and to work your way away from the
supply. Work the lawn at a suitable angle from the
power supply and place the power cable to the side,
which has already been aerated.
Warning: If the working condition does not allow the
motor to work at full speed, the motor power will drop.
If you hear a change in sound, stop working. Release
the switch lever and raise the working depth. Failure to
do so could damage the machine.
Note: The motor is protected by a safety device which
is activated when the blade becomes jammed or if the
motor is overloaded.
When this occurs, stop the machine and remove the
power cord from the power supply. The safety stop will
only reset when the switch lever A (illustration 1) is
released. Clear any obstruction and wait a few minutes
for the safety stop to reset before continuing to work.
During this time do not operate the switch lever as this
will prolong the reset time of the safety stop.
If the motor stops again, raise the working depth to
reduce the load on the motor.
When to use the aerator/scarfier roll
The aerator cylinder (blades) is used to aerate the
the lawn, providing more air to the roots of the
grass, so it can grow stronger and prevent moss.
The scarifier cylinder (springs) is used to remove
already existing moss in the lawn.
It is recommended to use both cylinders in combination
at least 2 times a year on your lawn: Spring and
autumn, and only when the ground is completely free of
frost.
… 9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas MPC 1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas MPC 1500 in the language / languages: English, Danish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info