514296

Texas Instruments eZ430-Chronos Manual

41
Zoom out
Zoom in
Previous page
1/113
Next page
www.ti.com
Data Logger PC Software
3.4.1 Detailed Feature Overview
As all available modes remain the same in the Data Logger software, only the additions are described in
this section.
3.4.1.1 Data Logger Mode
The data logger mode can be selected by pushing the "*" button until the bottom LCD line shows "dLog". It
may be enabled/disabled by pushing the "DOWN" button. If the heart rate data logging is selected (see
Section 3.5 ) in data logger PC software, the heart-rate monitor is automatically enabled (the RF icon
flashes until linked to a heart-rate monitor). When active, the record icon on the LCD is on (see
Figure 1-1).
NOTE: Connect the USB RF access point to the PC before launching the Control Center software.
For first time use, wait until Windows has finished the access point driver installation.
In case of problems on Windows PCs, check if the settings for the RF access point are
correct in the Windows Device Manager Start > Control Panel > System > Hardware >
Device Manager. The RF access point is listed under Ports (COM & LPT) as TI CC1111
Low-Power RF to USB CDC Serial Port. The port settings should be:
• Baud Rate: 115200
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
In case of problems on Linux PCs, ensure that the correct tty setting is specified. Check /dev
for the new tty device after plugging in the RF access point. If the RF access point is
assigned to a device other than ttyACM0, either remove the serial device that occupies this
slot (for example, a modem), or change the script file variable "com" in
eZ430-Chronos_Datalogger_1_2.tcl located in /home/<user name>/Texas
Instruments/eZ430-Chronos/Control Center/eZ430-Chronos Data Logger.
To launch the Control Center software, shortcuts are available in the Start Menu under Programs >
Texas Instruments > eZ430-Chronos > eZ430-Chronos Data Logger.
3.5 Data Logger PC Software
The eZ430-Chronos data logger PC software allows reading out logged data from the watch. It can also
be used to set and calibrate the watch, as its set modes were removed to free up as much memory as
possible for data logging. Available features:
• Time, date and calibration data synchronization tool
• Read out of logged data
• Wireless firmware update
To launch the eZ430-Chronos Data Logger software on a Windows PC, shortcuts are available on the
Desktop and in the Start Menu under Programs > Texas Instruments > eZ430-Chronos > eZ430-Chronos
Data Logger.
To launch the eZ430-Chronos Data Logger software on a Linux PC, browse to /home/<user name>/Texas
Instruments/eZ430-Chronos/Control Center/eZ430-Chronos Data Logger and run
eZ430-Chronos_Datalogger_1_2.tcl.
41
SLAU292D–November 2009–Revised March 2011 eZ430-Chronos Software
Submit Documentation Feedback
© 2009–2011, Texas Instruments Incorporated
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Instruments eZ430-Chronos at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Instruments eZ430-Chronos in the language / languages: English as an attachment in your email.

The manual is 7,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info