514296

Texas Instruments eZ430-Chronos Manual

25
Zoom out
Zoom in
Previous page
1/113
Next page
www.ti.com
eZ430-Chronos Sports Watch Software
3.2.1.5 Heart Rate Mode - RF
(2)
Press "*" until the heart icon appears on the display that is heart rate mode is active (see Figure 3-1 for
details). When this mode is active, heart rate is shown and burned calories are determined (additional
settings must be made for first time use, see Section 3.2.2.7). For information on how to use the chest
belt, see to the documentation included with the heart-rate monitor device.
NOTE: This mode requires a heart-rate monitor (chest belt) that is not included in this kit, but
available from BM innovations, Germany (see www.bm-innovations.com/chronos). However,
a heart rate can be simulated without a chest belt by the eZ430-Chronos Control Center, see
Section 3.3 for details.
While almost all other eZ430-Chronos functions are based on TI's SimpliciTI protocol, the
heart-rate monitoring uses BlueRobin, an ultra-low-power low-data-rate wireless
communication protocol from BM innovations.
Secondary function: Heart rate display on/off. Press "UP" to enable/disable the heart-rate monitoring.
Once a connection is established, the heart rate is shown on the top LCD line
Set function: None
3.2.1.6 Speed Mode - RF
(3)
Press "*" until the "mi/h" or "km/h" icon is shown on the display; that is, the speed mode is active (see
Figure 3-1). Your running speed is shown on the LCD top line.
NOTE: This mode requires a heart-rate monitor (chest belt) which includes an accelerometer to
determine running speed. Visit BM innovations at www.bm-innovations.com/chronos for
available additions. However, speed can be simulated without a chest belt by the
eZ430-Chronos Control Center, see Section 3.3.4 for details.
While almost all other eZ430-Chronos functions are based on TI's SimpliciTI protocol, the
speed mode uses BlueRobin, an ultra-low-power low-data-rate wireless communication
protocol from BM innovations.
Secondary function: None
Set function: None
3.2.1.7 Tilt Mode
Press "*" until the tilt mode is active (see Figure 3-1). The acceleration is shown in G (9.81 m/s
2
) for all
three axes. After entering the tilt mode, the y-axis acceleration is shown by default, and the z-axis or
x-axis can be selected. Positive acceleration values are marked with a small arrow pointing up in the top
LCD line, left of the acceleration. Negative acceleration values are marked with a small arrow pointing
down. After 60 minutes, a timeout deactivates the measurements.
Secondary function: Select axis. The default is y-axis, followed by z-axis and x-axis.
Set function: None
(2)
Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
(3)
Additional accessory or eZ430-Chronos Control Center heart rate simulation required.
25
SLAU292D–November 2009–Revised March 2011 eZ430-Chronos Software
Submit Documentation Feedback
© 2009–2011, Texas Instruments Incorporated
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Instruments eZ430-Chronos at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Instruments eZ430-Chronos in the language / languages: English as an attachment in your email.

The manual is 7,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info