Manual Texas Fusion 10B (page 17 of 32) (English, German, Danish)

636688

Zoom out

Zoom in

1/32

Cleaning the tiller

The tiller should be cleaned after use. Use a garden

hose to wash off soil and dirt. Remove any grass, etc.

from the rotor shaft. The chassis number should only be

cleaned with a damp cloth to avoid unnecessary wear.

Avoid using a high-pressure washer during cleaning.

Changing the oil

The oil should initially be changed after the first 5 hours

of use, and thereafter once per year.

1. Let the motor run for 5 minutes to heat up the oil.

This allows the oil to run more freely and makes for

a more complete oil change.

2. After 5 minutes, stop the motor. Remove the spark

plug cap. Drain the oil by unscrewing the sump

plug. Remember to drain the oil into a container of

sufficient capacity. NB: The motor must not be

tipped backwards more than 45 degrees.

3. Screw the sump plug back in and pour new oil into

the motor. Do this by removing the dipstick and

pouring in the recommended quantity of oil.

4. Refit the spark plug cap.

Alternatively, use an oil extractor kit:

1. Suck the oil up through the oil filler hole using the

syringe. Use the hose to reach the sump.

2. Transfer the used oil to the container.

3. Fill the engine with new SAE-30 oil.

4. Check the oil level reaches the edge of the filling

hole (Fig. 21).

Remember to dispose of used oil in a safe way.

Oil and oil extractor kit are not included

Air filter maintenance

Please inspect and clean the air filter on a regular

basis. If the filter has not been cleaned for a longer

period, this will have influence on the engines power

take-off and the exhaustion.

1. Clean around the air filter before it is removed.

2. Carefully remove the paper filter and check it.

Brush it with a soft brush. If it is very dirty, it must

be changed. Take care that no dirt gets into the

intake of the engine.

3. Wash the black foam element on the right side in

warm soapy water.

4. Press the water out of the foam element and let it

dry. Put a few drops of SAE-30 oil on the filter to

moisten it lightly with oil. Carefully squeeze out any

surplus oil. Remount the element.

5. Check that all parts are fitted correctly and the

cover closed as shown in the picture.

See the engine user manual for further information.

Spark plug maintenance

• Remove the spark plug cap.

• Brush away any dirt and deposit of the spark plug.

• Loosen the spark plug using a spark plug socket.

• Check the insulation is intact.

• Clean the spark plug using a wire brush.

• Measure the electrode gap 0.7–0.8 mm. Avoid

damaging the electrode.

• If it is damaged, replace it with a new one.

• Refit the spark plug.

• Refit the spark plug cap.

Storage

• If the machine is likely to be stored unused for

prolonged periods, follow the instructions below.

This will ensure longer machine lifetime.

• Use a garden hose to wash off soil and dirt.

Remove any grass, etc. from the rotor shaft. The

chassis number should only be cleaned with a

damp cloth to avoid unnecessary wear. Avoid using

a high-pressure washer during cleaning.

• Wipe the tiller with a damp cloth so that all surfaces

are clean. Wipe the surfaces down with an oily

cloth to prevent rust.

• Always store the machine in a dry, clean location.

Troubleshooting

The motor will not start

1. Check the fuel control is set to level “4”.

2. Check the spark plug.

3. Check there is fresh gas in the tank.

4. See separate motor instructions for further

troubleshooting.

The motor is not running smoothly

1. Ensure the choke is completely turned off.

2. Check there is fresh gas in the tank.

The blades will not rotate

1. Check for stones lodged between the blades.

2. Release any stones by removing the blades.

3. Check the cables are in good working order and

fitted correctly.

4. Check the belt is in good working order and fitted

correctly.

5. Ensure the belt tensioner is adjusted correctly.

The blades will not stop

1. Stop the engine and contact your dealer.

2. Check that he belt pulley is adjusted correctly.

Engine will not stop

1. Adjust the throttle cable

Noise, vibration and precautionary measures

1. Long-term exposure to noise levels exceeding 85

dB (A) are damaging. Always use ear defenders

when the machine is being used.

2. Reduce the running speed of the motor to reduce

vibration and noise levels.

3. To reduce noise levels further, only use the

machine in an open environment.

4. Vibrations can be reduced further by holding the

handle firmly.

5. To avoid disturbing others, the machine should only

be used during the daytime.

6. Always wear close-fitting work clothes, hard-

wearing work gloves, ear defenders and non-slip

boots with steel toecaps.

7. Take a 30-minute break every 2 working hours.

8. A worn belt has to be replaced/ serviced by a

authorized dealer

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas Fusion 10B in the language / languages: English, German, Danish as an attachment in your email.

The manual is 5,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas Fusion 10B Manual

Product: