636688

Texas Fusion 10B Manual

16
Zoom out
Zoom in
Previous page
1/32
Next page
16
from the rod (C) to lock the wheel assembly into
position.
Adjustment of depth skid
The depth skid can be set to 3 different depths. The
deeper it extends into the soil, the deeper the tilling
blades will work and the slower the machine will
advance. Setting the correct tilling depth will
significantly reduce the effort required. The depth skid
should always be adjusted to suit the ground conditions.
We recommend testing several depths to see which
works best.
Lubrication of gearbox
The gearbox is filled with gear oil at the factory.
Check oil level (the oil level should be visible for the
eyes
, when the oil cap is removed - Fig. 17) and fill up
with gear oil after the first 20 and 50 working hours.
Fill with gear oil type GL-5 / SAE 80W/90.
Do not overfill with oil.
For every 100 working hours, the gear oil must be
replaced. Remove the drain plug (Fig. 18) and let the oil
run out into a plastic tub or similar.
Tip: It is recommended to let the tiller blades rotate for
a while before draining the gearbox. It will make the
gear oil warm, so it runs out easier.
Fill with new gear oil (about 1.2 - 1.3 liter)
Starting and stopping the engine
Remember: Always check the oil level prior to use!
The oil level must reach the edge of the filling hole
(Fig. 21). Always use SAE-30 oil. Use only unleaded 95
octane gas. Never over-fill the gas tank.
Warning: Stay out of dashed zone, while starting the
engine!
Always start the engine from dotted operation zone See
red color in Fig. 20 .
Starting the engine
1. Set the throttle control on the handle to “4”
(Fig. 13B)
2. Open the fuel tap, if engine is fitted with this.
3. Position the choke at max.
The choke is not required if the motor is hot.
4. Pull the start cord to start the motor. Always feed
the start cord back into the motor by hand.
5. When the motor is started, set the choke to
minimum.
Stopping the engine
1. Set the throttle control to “1” and let the motor run
for approx. 30 seconds.
2. When the motor idles, set the throttle control to
“Stop”.
Vibrations may travel up into the handle
during use. We therefore recommend taking
a break every 2 hours.
Accessories overview
Severa
l accessory options are available for FUSION 10.
See Fig. 22 on page 5.
Texas recommend buying accessories, as it increases
the usage possibilities of the machine considerably.
Below accessories can be purchased for use with
FUSION 10 (the list is subject to local
changes/availabilities):
Tilbehør Nr.
Wheels: used to mount accessories, such as
rake.
Art. no. 91075500100
1
Digging claws: used if the soil is loose or
muddy and the machine is to be operated with
a ridge plough or harrow instead of wheels.
Art. no. 91075300100
2
Side discs: used for tilling in between crops,
such as carrots/potatoes, to avoid covering the
crops in soil. Side guards can also be used for
tilling along a wall or stone path, or in soft soil.
Art. no. 91075700100
3
Weight blocks: used to give the machine a
better grip when operating with a trailer or
snow blade.
Art. no. 91075400100
4
Rake: used to rake paths and entrances with
loose stones, for instance pebbles.
Art. no. 91062500100
5
Harrow: used to loosen the soil between crops
and thus remove weeds.
Art no. 91070000100
6
Weeder: used to loosen the soil and thus
remove weeds on paths and entrances.
Vare nr. 91061500100
7
Scarifier: used to aerate the lawn and remove
underlying dead grass from the lawn. The
grass grows greener and stronger, which
prevents the grown of moss.
Art. no. 91051550100
8
Potato plough: used for harvesting potatoes
Art. no. 91061200100
9
Trailer with seat: used for transport of various
materials.
Art. no. 91075000100
10
A
ssembly plate: used to attach front mounted
accessories.
Art. no. 91075600100
11
Snow blade: used to scrape snow from a solid
surface, such as paving slabs. Can be tilted to
the left/right. The assembly plate is necessary
for fitting.
Art. no. 92000160100 + 91075600100
12
Ridger: used to plough up ground for
potatoes, carrots and other root crops.
Art. no. 91076100100
13
Plough: used to turn the soil.
Art. no. 91076000100
14
Turning plough: used to turn the soil. Can be
rotated 180
o
.
Art. no. 91076200100
15
Rain-cover: used to protect the machine from
dirt or rain during storage.
Art. no. 40-11720
16
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Fusion 10B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Fusion 10B in the language / languages: English, German, Danish as an attachment in your email.

The manual is 5,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info