Manual Texas COMBI 800TGE (page 13 of 29) (English, German, Danish, French)

636684

Zoom out

Zoom in

1/29

Note: The clutch lever is not broken but simply pushed

back into place.

The machine is equipped with a "dead man's handle",

once released the brush and drive will stop

immediately.

Wheel shaft: Fixed vs. free

• Activate free wheel shafts, see fig. 7-A

At hard ground (e.g. paved road), it can be a

good idea to activate free wheel shafts.

• Activate fixed wheel shafts, see fig. 7-B

At soft/lose ground (e.g. dirt road) it can be a

good idea to activate fixed wheel shafts

Generally, the machine will be easier to manoeuvre

with free wheel shafts.

Operation safety zone

Do not leave the operation safety zone marked in fig 5,

while working with the machine. If it is necessary

toleave the operation zone, for example to readjust the

rotary brush or to attach an accessory, first stop the

engine.

Angle adjustment of accessory

The accessory can be pivoted 20 degrees to either

side. This is done by pushing the swing handle down,

turning the brush and releases the handle so the

detent clicks into place.

Changing of handlebar height

1. Remove the small bolt from the gear rod

middle part (fig. 6-B).

2. Loosen the 4 bolts on the middle of handlebar

(fig. 6-A) and take the out.

3. Move the upper handlebar and the gear rod

part up/down with same number of holes

(fig. 2-F+G)

4. Mount all the bolts again on the handlebar and

gear rod and tighten them again.

5. Check that the gear rod (fig. 6-C) easily can

move into all position. If not, the bolt on the

gear rod middle part is probably not placed in

the correct hole.

Storage

Correct storage of your sweeper!

Store the sweeper, so that the brushes do not touch

the ground. This will extend the durability and lifetime

of the brushes.

• Lower the support wheels about 50 mm so that

the brushes are floating above the ground

before the sweeper is disconnected from the

basis unit.

• Disconnect the sweeper from the basis unit.

• Tilt the sweeper back, so it rests on the

connection-part, and let it stand in that position

during the storage period.

Never let the brushes rest on the ground for longer

time. It will cause them to bend and be useless. Fig. 10

Troubleshooting

Problem Solution

The engine won't start:

1. Check sparkplug.

2. Check that the spark plug cap is fitted

correctly.

3. Check if the motor is equipped with an

ignition switch.

(It must be activated)

4. Check if the motor is equipped with a

fuel valve.

(It must be activated)

The engine runs unevenly:

1. Check that the choke has been released.

2. Check fuel for impurities

(or check/clean the carburetor)

If the accessory-unit makes noise or run badly:

1. Check that the accessory-unit is clicked

in place properly (fig. 5-A).

If the accessory-unit will not run:

1. Check that the cable is adjusted

correctly.

If the machine will not run:

1. Check that the cable is adjusted

correctly.

2. Check the belt.

If the machine does not sweep effectively:

1. Check the distance between the brush

and working surface.

Technical specifications

Model

Combi

800 TG

Combi

800 TGE

Combi

800 B

Length (mm) 800 800 800

Width (mm) 700 700 700

Height (mm) 1000 1000 1000

Weight, dry (kg) 55.5 56 55.5

Wheel size 4.80-8 4.80-8 4.80-8

Engine model TG720S TG720ES 950

Engine brand

Texas

Powerline

Texas

Powerline

B&S

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas COMBI 800TGE in the language / languages: English, German, Danish, French as an attachment in your email.

The manual is 2,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas COMBI 800TGE Manual

Product: