686244
22
Zoom out
Zoom in
Previous page
1/52
Next page
22 • Impaq 8000
Menu “Speaker settings”
“Channel configuration”
Here you can specify the channels, which the speak-
ers are connected to. This ensures that the system
is able to optimally distribute the audio signal among
the speakers.
2.1 Only the front speakers on the left/right and
subwoofer.
5.1 All channels have been assigned speakers.
7.1 The (rear) channels are also connected via
the output AUX OUT / RC PRE OUT (20).
If the configuration is changed, the menu “Speaker
size” (see below) will automatically appear.
“Speaker size”
Here you can set the size of the speakers in use for
optimal actuation of the speakers. Depending on the
setting for “Speaker configuration” (see above), differ-
ent configurations are available for selection; they are
shown as a series of letters/numbers and graphically:
The letters represent the speakers:
Front channels
center
surround channels
rear channels
In this context, S stands for small and L for large
speakers.
The end number indicates whether a subwoofer is
present (“1”) or not (“0”).
Examples:
S1: 2.1 system, small front speakers with a
subwoofer
LSS0: 5.1 system, large front speakers, small
center and surround speakers, no subwoofer.
LLLL1: 7.1 system, all large speakers, subwoofer
present.
“Crossover frequency”
If you use satellites and subwoofers, you should select
the optimal crossover frequency in the Impaq 8000.
Otherwise, the sound quality will suffer and the satel-
lites could be damaged.
With the crossover frequency, you define the frequen-
cy up to which the subwoofer and satellites should be
active. Possible values: 80 to 250 Hz in ten steps.
You can find information on the recommended cross-
over frequency in the technical data of the respective
satellite speakers in our webshop.
“Subwoofer phase”
You can hereby switch the phase shift (180°) on and
off for the subwoofer. Select the setting, with which
the subwoofer produces the loudest and clearest
sound.
Menü “Audio setup”
“HDMI transit”
If you switch to standby from HDMI mode, an HDMI
input signal will either be transmitted to the HDMI
output or blocked depending on the setting.
• On – signal will be transmitted in standby
Off – signal is blocked.
“HDMI audio output”
Switches the audio transmission to the TV set on and
off at the HDMI output HDMI TV (13).
When playing back movies, you do not need to mute
the television in the “Deactivate” position in order to
hear sound from the receiver’s speakers only.
“HDMI output”
Determines the audio output at the HDMI output
HDMI TV (13). Possible values:
PCM – The audio signal is mixed to 7.1 and trans-
ferred as PCM (normal setting).
Bitstream – Passes on the data stream from the
Blu-ray disc unchanged (only for TV sets with Dolby
and DTS playback).
Bitstream recoding – Passes the data stream of
the Blu-ray disc mixed and coded in a single data
stream. Suitable for Dolby TrueHD and DTS-HD
Master Audio.
“Down sampling”
Determines the sampling rate of the audio signal.
Possible values:
48 kHz – corresponds to CD quality
96 kHz – corresponds to DVD quality
192 kHz – no down-sampling (Blu-ray quality)
Settings
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teufel Impaq 8000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teufel Impaq 8000 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Teufel Impaq 8000

Teufel Impaq 8000 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info