688826

Telair TIG3000B Inverter generator Manual

21
Zoom out
Zoom in
Previous page
1/44
Next page
Vers. 001
TIG 3000 B
21
GB
charger used and the ambient temperature in the
battery environment.
In the event that, in addition to the battery
charger, a minimal default load is connected
(around 300 Watt), the generator will not shut off.
The AUTO mode can be activated whether the
generator is active or on stand-by.
The AUTO mode is automatically deactivated
when the START/STOP button is pressed.
8.7 Remote starting
The generator can be started using a remote
control from another device (battery charger,
SMS box, etc.), using the REMOTE connector
(Fig. 22 ref. 4). The galvanically isolated C and
NO terminals are attached to this connector by a
relay controlled from an external device.
To carry out a remote start-up, turn the switch on
the control panel to the ON position (Fig. 30 ref.
1), without starting the generator. At this point the
generator is ready to receive a command on the
REMOTE connector: when the contact is closed,
the generator will start and it will stop when the
contact is opened.
Should any high-level alarms come from
the generator, such as oil or temperature, the
signal from the D+ input, or pressing the
START/STOP button on the control panel will
take priority over the REMOTE On-Off command.
The oil alarm and the D+ signal prevent remote
start-up until the START/STOP button on the
control panel has been pressed.
8.8 BOOST Function
The BOOST function must be activated when a
single load close to the maximum power must be
connected.
To activate this function, hold down the Menu key
for 3 seconds; the corresponding LED lights up
and even in the absence of any load the engine
increases its rpm.
To turn off the function, press and hold the Menu
key again for 3 seconds; the corresponding LED
will go off and the engine rpm slows down.
8.9 Alarm messages and causes
The alarms described here stop the generator.
An alarm condition is cancelled by pressing the
START/STOP button once; the generator then
reverts to a status in which it can be restarted.
Before doing this, you must eliminate the condi-
tion that caused the stop and the alarm.
8.9.1 Over load
the maximum
permitted load has been exceeded, the generator
stops and the red alarm LED lights up (Fig.30 ref.
8).
8.9.2 Short circuit
there is a
short circuit on 230 V output, the generator stops,
the red alarm LED lights up (Fig.30 ref. 8).
8.9.3 Low output voltage
the output
voltage has dropped too far below the minimum
limit, probably due to poor performance of the in-
ternal combustion engine or to a single very high
load being applied without the use of the BOOST
function, the generator stops, the red alarm LED
lights up (Fig. 30 ref. 8).
8.9.4 Oil pressure
insufficient
engine oil lubricant level or pressure has been
detected, the generator immediately stops and
the red alarm LED lights up.
8.9.5 Engine temperature too high
an exces-
sive engine temperature has been detected, the
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telair TIG3000B Inverter generator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telair TIG3000B Inverter generator in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telair TIG3000B Inverter generator

Telair TIG3000B Inverter generator User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info