Manual Teka IRC 631 (page 20 of 25) (English, German, French)

781071

Zoom out

Zoom in

1/25

2The countdown will stop and the indica-

tor (7) displays 00. A blinking will dis-

play on the indicators for each of the pla-

tes that are powered up.

3At that point, you can time another plate

or alter the remaining time on a pre-

viously time set plate. To distinguish

them, take into account the decimal

point appearing on the bottom right

of the indicator (3), only on that/those

plate/s that are timed at that moment.

In the next 5 seconds, touch one of the

sensors (4) or (5) corresponding

to the plate that you wish to time or alter.

The will stop blinking in the indicator

for this plate and the digits on the indica-

tor (7) of the clock will start to blink.

4Touch the sensors (11) or (12)

again until the required time is set. After

a few seconds the decimal point in the

indicator (7) will start to blink, indicating

that the countdown has started.

If you wish to cancel a timing already set,

simply set the time desired in step 4 to 00 or,

directly, by turning off the plate in question.

When you have timed more than one

plate, by default, the indicator (7) of the

clock will display the shortest remaining

time. This time will correspond to the plate

whose indicator (3) displays the blinking

with the decimal point.

Remember that the decimal point in a

power indicator (3) shows you that this plate

is timed! If this decimal point is blinking and

it’s shown the , it means that the indicator

(7) of the clock is showing you, at that pre-

cise moment, the time remaining in the

countdown for that hotplate.

Please remember that if, during the

countdown, you turn off the touch panel

using the on/off sensor button (1),

the countdown will be cancelled!

Overheating safety feature

The induction areas are protected against

overheating that may cause damage to the

electronic system.

The internal fan is automatically enabled

and disabled, depending on the tempera-

ture of the electronic system. Therefore,

the fan may continue to work for a few

minutes to cool the electronics if you

switch the cooker off when the fan is swit-

ched on.

Power surges

Touch controls can withstand a

certain degree of power surges in the

electricity supply. Abnormally high

power surges can cause the control

system to malfunction (as with any type

of electrical appliance).

Suggestions and

recommendations

To ensure maximum performance from

your hob, follow these guidelines:

*Use pans with a flat base, as the greater

the surface contact between the pan

and the glass, the greater will be the

heat transmission. We recommend the

use of heavy pans so that the base is

more difficult to dent. Figure 4 shows

how pans that are dented or concave

have a smaller contact surface.

fig. 4

Right Wrong Wrong

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Teka IRC 631 in the language / languages: English, German, French as an attachment in your email.

The manual is 0.86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Teka IRC 631 Manual

Product: