Manual Teka IRC 631 (page 19 of 25) (English, German, French)

781071

Zoom out

Zoom in

1/25

Be careful not to touch different sensors

other than (11) or (12) since, by

doing so, a plate may cease timing instead

of programming the chronometer.

Once the countdown has reached zero, a

series of bleeps will be heard. These can

be cancelled by touching any of the sen-

sors (11) or (12) associated with

the clock.

If, while the clock is working as a count-

down chronometer, at some point the

induction plates are set at power level 0,

the touch control panel will turn off after a

few seconds, but the chronometer will con-

tinue working until it finishes the count-

down or the countdown is cancelled.

To cancel the chronometer, simply set the

remaining time to 00.

Timer function

(except models …630)

This function will help you with cooking as

you will not have to be present during the

following: the timer plate(s) will automati-

cally turn off at the end of the set time. The

device has an individual timer for each

plate. This allows it to time all the plates at

the same time, if required.

The function is controlled with the time

increase/decrease sensors and

(11/12) associated with the clock (7).

SINGLE plate timer

To activate the timer on one single plate,

proceed as follows:

1With the plate powered on and the clock

turned off, touch one of the sensors

(11) or (12) corresponding to the

clock.

2Turn on the indicator (7) displaying 00.

At the same time, a blinking will appe-

ar on the indicators for each of the pla-

tes that are powered on.

3In the next 5 seconds, touch one of the

sensors (4) or (5) correspon-

ding to the plate you wish to time. The

will be set on the indicator for this

plate and the digits on the clock indica-

tor (7) will start to blink.

4You have a further 5 seconds to select

the time required, simply by touching the

sensors (11) or (12) on the

clock. After a few seconds, the digits on

clock indicator (7) will stop blinking and

the decimal point on the clock and the

timed plate will start to blink, indicating

that the countdown has started.

Once the required time has been set, be

careful not to activate any other sensor

since the device may interpret that you

wish to exit the timer function. While the

clock digits blink, you can alter their value

but do not touch different sensors other

than (11) or (12).

Once the countdown is complete, the

timed plate will power off and a series of

bleeps will be heard that can be cancelled

by touching any of the sensors (11) or

(12) associated with the clock.

Timing more than one plate / Altering

the programmed time

During a countdown, you can alter the

remaining time or time a new plate.

1With the Touch Control powered on and

a plate timed, touch one of the sensors

(11) or (12) corresponding to the

clock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Teka IRC 631 in the language / languages: English, German, French as an attachment in your email.

The manual is 0.86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Teka IRC 631 Manual

Product: