18328

Teka CI345.1 Manual

10
Zoom out
Zoom in
Previous page
1/20
Next page
FITTING THE APPLIANCE INTO COLUMN CABINETS
Double doors and combis
The built-in dimensions are shown in fig. 14/15.
Proceed as follows to fit the appliance:
- Fit gasket 1 (provided with the appliance) to the side opposite the hinges (fig. 5).
- Fit the appliance into the column cabinet, setting it flush to the side without hinges and
push backwards so that a distance of 45 mm. is achieved between the appliance and the
front of the cabinet (fig. 6).
- Fix the appliance firmly at the top and bottom with the screws provided in the accesso-
ries pack and snap fit the ventilation grid into position (fig. 7).
Furthermore, for those models with lateral fixing clamps, proceed as follows (fig. 8):
- Centre hinge side - slacken off hinge fixing screw 1 and offer up clamp 3 to the column.
- Opposite side from the centre hinge - remove the clamp cover 2 and offer up the clamp
to the column.
- Screw the clamps to the column using the screws to be found in the accessory pack and
tighten the screws lackened off previously.
- Refit the clamp cover.
HOW TO COUPLE THE DOORS OF THE APPLIANCE
WITH THOSE OF THE COLUMN CABINET
The appliance is fitted with devices to couple its doors with those of the column cabinet
(dragging slides). The slides should be fitted as follows:
- (Fig. 9) Fix slide 1 to the door of the cabinet at the desired height and at approximately
20 mm. from the side edge of the door.
- (Fig. 10) Open the cabinet and refrigerator doors and fit the coupling device 2 onto slide 1.
- Keep the coupling 2 aligned with the refrigerator door.
- Mark the drilling points for the screws and drill 2,5 diameter holes.
- The slots in the coupling 2 facilitate easy adjustment.
- It is recommended that the dragging slides are fitted to the appliance door in correspon-
dence with the column door handles.
Furthermore with models fitted with extra handles for opening the door, proceed as fol-
lows (fig. 11):
- Offer up handle 1 to the door, then drill a hole corresponding to the one on the handle.
- Screw home using the screws in the accessory pack.
ADVICE FOR PROPER OPERATION
To obtain the maximun efficiency from your appliance it is important to allow good
ventilation to the system in order to cool down the condenser positioned at the
rear of the appliance.
DOUBLE DOOR COMBI AND SINGLE DOORS
To this end an opening must be made in the bottom of the column for an air inlet
(fig. 13). For the air outlet the column should be equipped with an upwards direc-
ted, unobstructed rear vent.
Should the column be flush fitted to the ceiling, such an outlet should be present
between it and the ceiling (fig. 13).
The appliance should not be installed in areas where the temperature remains belows
+16°C or above +32°C for long periods.
10
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka CI345.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka CI345.1 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info