536100
87
Zoom out
Zoom in
Previous page
1/200
Next page
Part IV Sequencer
87
QQTG0692
Sequencer
Any panel setting changesfor example
changes in the sound selection, button oper-
ation, wheel operation, etc.are recorded at
the cursor position.
When a wheel or dial is operated, the input
value is indicated on the display. Confirm
that this is the correct value and press the
YES button to record the value or the NO
button to cancel it.
REST:
To store a rest, after specifying the note
LENGTH, press the REST button.
Positions at which nothing is stored are read
as rests.
ERS:
If you make a mistake, move the cursor to
the error, and after displaying the data you
wish to erase, press the ERS button.
BAL:
To specify the volume at the cursor position,
after pressing the BAL button, use the
VALUE buttons to set the volume (0 to 127).
9.
Repeat steps 4 through 8 to continue storing
notes.
To input data on another track, press the but-
ton for the desired track and repeat the pro-
cedure from step 2.
10.
When you have finished recording, press the
PROGRAM MENUS button to turn it off.
Storing control data
Various control data can be stored at the cursor
position.
1.
On the STEP RECORD: MELODY display,
press the CTL button.
2.
Use the CTL
and
buttons to select the
control data you wish to insert.
Select from PAN, KEY SHIFT (COARSE
TUNE), TUNING (FINE TUNE), BEND SENS.
3.
Use the VALUE
and
buttons to adjust the
numerical value of the setting.
4.
Press YES button.
Correcting the data
1.
In the STEP RECORD mode, specify the track
you wish to correct.
2.
Use the MEAS buttons to go to the measure
you wish to modify. Use the CURSOR buttons
to move the cursor to the point (
) you wish
to edit.
The data stored at that point is shown on the
display.
When multiple data is stored at one point, dif-
ferent data is displayed in order each time a
CURSOR button is pressed. When a chord is
recorded, a different note in the chord is dis-
played each time a CURSOR button is
pressed.
3.
Correct the data.
There are three types of data:
Performance data
NOTE data (note pitch) and VEL data (how hard
the key was played) and LEN data (1 = 1/96 of a
quarter note [
q
]) are displayed. Use the relevant
buttons to correct the data as desired.
Sound data
The name of the sound is displayed. Change the
sound as desired (the sound setting display is
interposed on the current display).
Control data
The name of the function is displayed. Change
the data as desired.
Press the ERS button to erase the data which
is displayed.
You can also correct data which was stored in
the REALTIME RECORD mode.
Performance (NOTE) data can be recorded or
edited on a piano roll display, and there is also
a specialized display for recording and editing
the DRUMS part data. (Refer to page 94.)
09_Part IV.fm 87 ペー ジ 2003年2月 5日 水曜日  午後1時34分
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SX-KN2600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SX-KN2600 in the language / languages: English as an attachment in your email.

The manual is 7,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info