536100
86
Zoom out
Zoom in
Previous page
1/200
Next page
Part IV Sequencer
86
QQTG0692
Sequencer
Step Record
STEP RECORD is simply a method of making a tune by storing the sounds note-by-note on the display.
Instead of playing the keyboard directly as in the REALTIME RECORD mode, you can take your time to
input each single note. This is an especially effective method for storing complicated passages that are
difficult to play or when the exact timing of a part is critical.
Recording procedure
Record the keyboard performance and panel
changes.
1.
On the SEQ MENU display, use the SONG
SELECT
and
buttons to select the song
number. Then select RECORD & EDIT.
2.
On the RECORD & EDIT display, select STEP
RECORD.
The display changes to the PART SELECT
display.
3.
Use the balance buttons below the display to
specify the track for the part you are going to
record (only one track can be selected at a
time).
The display changes to the STEP RECORD
input display similar to the following.
If you selected the track to which the CHORD
part has been assigned, the display changes
to the STEP RECORD: CHORD display.
(Refer to page 88.)
If you selected the track to which the
RHYTHM part has been assigned, the display
changes to the STEP RECORD: RHYTHM
display. (Refer to page 90.)
If you selected the track to which the CON-
TROL part has been assigned, the display
changes to the STEP RECORD: CONTROL
display.
4.
Use the MEAS
and
buttons to select the
measure.
This step is not necessary if you are recording
from measure 1 of a blank track.
5.
Use the CURSOR
and
buttons to move
the cursor to the note position (dot) you are
going to store.
Each dot represents one-eighth of a quarter-
note (a thirty-second note).
When storing triplets, it may not be possible to
match the timing exactly with the 1/32-note
steps. However, if you select triplet-type notes
for the note length (LENGTH) in step 6 below,
the timing is automatically corrected.
6.
Use the left REC NOTE LENGTH
and
buttons to specify the note value. Select from
r
3
,
r
,
x
3
,
x
,
e
3
,
e
,
q
3
,
q
,
h
,
w
,
w
× 2 to 4. (A 3
denotes a triplet-type note.)
For note values other than these, use the cen-
ter REC NOTE LENGTH buttons to specify
the note value to be added to that which you
specified with the left buttons.
Example: To record a dotted quarter-note
(
q
.
)
q
+
e
7.
Use the right REC NOTE LENGTH
and
buttons to specify the actual length of the
produced sound for the desired legato or
staccato effect.
8.
Specify the pitch and velocity of the note by
playing the keyboard.
The dot on the display where the note is
stored changes to a
mark.
When recording chords, you can store multiple
notes at one position.
TENU (tenuto): Sound is produced for 95%
of the note length.
NORM (normal): 80%
STAC (staccato): 50%
CUTT (cutting): 25%
09_Part IV.fm 86 ペー ジ 2003年2月 5日 水曜日  午後1時34分
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SX-KN2600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SX-KN2600 in the language / languages: English as an attachment in your email.

The manual is 7,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info