637111

Technics SC-CH515 Manual

35
Zoom out
Zoom in
Previous page
1/60
Next page
Closing up the tape-end unrecorded sections
(LAST FADE)
ASTFADE Press LAST FADE.
I
Lights.
The recording will start after the system completes steps 2-3 of
"One-touch operation" below.
Use this editing mode when you record the tracks numbering higher
than 24.
You can edit the desired tracks of the desired disc(s) using this
editing mode. (See "Program edit recording" on page 36.)
fAv_'_
To cancel one-touch editing:
Press [] on the cassette deck.
The compact disc changer also stops.
One-touch editing operation:
1. The cassette deck will fast-forward and rewind to measure its
length. At the same time, CCRT function will be activated.
(See page 31.)
2. The cassette deck will automatically advance the tape beyond
the leader tape, and then stop.
3. The compact disc changer automatically scans for the peak
(highest) level of the entire disc (Automatic Tape Level Set-
ting--ATLS), then recording will start. ATLS is the function which
scans (fast search) for the peak (highest) level of the disc, and
sets the appropriate recording level. When ATLS is activated, no
sound will be heard.
It takes about 70 seconds to complete ATLS for a compact disc of
60 minutes.
When there are tracks allotted on tape side B:
The cassette deck will continue recording a blank portion on tape
side A until the end of the side.
To record with desired tone quality:
Select the desired tone quality (see pages 42-44), and start editing.
To play back such recordings, press ON/FLAT on the tuner/sound
processor to set to FLAT.
To specify the tracks to be edited:
You can specify the tracks to be edited using the program play
procedure. (See page 22.)
After completing step 5 on the previous page:
1. Press PROGRAM on the remote control, and then specify the
tracks to be recorded in the desired sequence.
2. Press one of the one-touch editing buttons (ALBUM, J.FIT, LAST
FADE) to start editing.
You can program up to 24 tracks (and also tracks numbering lower
than 24).
"FULL" appears on the disptay if you try to program more than
24 tracks.
After the edit recording has finished:
When one disc is loaded:
The deck automatically enters the recording standby mode. When
"LINK" indicator flashes, it means you can edit tracks from the same
or another disc in succession. (See page 37.)
When two or three discs are loaded:
When there isa blank portion on the tape, the deck will automatically
start recording from the next compact disc.
When "LINK" indicator flashes after recording of all the loaded discs
has finished, it means you can edit tracks from the same or another
disc(s) in succession.
To finish recording:
Press [] on the compact disc changer and "LINK" indicator goes off.
35
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SC-CH515 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SC-CH515 in the language / languages: English as an attachment in your email.

The manual is 6,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info