637111

Technics SC-CH515 Manual

31
Zoom out
Zoom in
Previous page
1/60
Next page
To stop recording:
_] Press 13.
To cut an unnecessary part while recording:
1. Press REC PAUSE.
The cassette deck will go into the recording standby state.
2. To resume recording, press <3 or D corresponding to the direc-
tion in which recording is taking place.
CCRT recording function:
CCRT (Computer Control Record Tuning) is the function which iden-
tifies the quality of the tape (concerning bias, level, equalizer) auto-
matically and sets the most desirable recording condition. While the
CCRT setting is activated, the CCRT indicator flashes. After the
setting has completed, CCRT indicator stops flashing.
The CCRT setting will remain in the system's memory even after the
power is switched to the standby mode.
The display shows the CCRT setting conditions as follows:
1. Bias setting
2.
3.
TIT L_IL.
III I1_1
I I
Recording level setting
il ;- FI
!
!
!
Recording equalizer setting
'--
'1
I
iF--Ul
CCRT setting has been completed: "SET OK"
I
:f--Ill
oYou can make recordings in constant tone quality with use of the
CC RT function regardless of the different characteristics.
oWhen making an edit-recording from a CD, the CCRT function will
be automatically activated.
f_
• Do not press INT or EXT while the CCRT is setting.
eDo not insert or remove the cassette tape after the CCRT setting
has been completed. It cancels the CCRT setting.
eThe CCRT setting may not be possible with the old cassette tape or
at around the end of the cassette tape. (The CCRT indicator starts
to flash at a high speed.) In this case, press [] and record without
using the CCRT function. (The CCRT indicator goes out.)
oDe not connect or disconnect the microphone while recording.
L__J To cancel the CCRT setting on the
way:
Press N.
CcRTO
%
To cancel the CCR'I- after the CCRT set-
ting has completed:
Press CC RT.
To erase a recorded sound (Deck 2):
When you make a new recording on a previously recorded tape, the
new recording will automatically erase what was previously re-
corded. To erase a recorded sound without making a new recording,
perform the following steps:
1) Disconnect the microphone if it was connected.
2) Press INT to select the tape mode.
3) Insert the recorded tape intothe cassette holder of deck 2.
4) Press DOLBY NR to light up Dolby NR OUT indicator.
5) Select the desired reverse mode.
6) Press REC PAUSE.
7) Press the playback button (<3 or D) corresponding to the side to
be erased.
To take up the leader tape
The leader tape is the first few revolutions that you cannot record on.
Magnetic tape
(recordings can be made)
Leader tape
(no recordings can be made)
To record with desired tone quality
To record with the desired tone quality, follow the procedure below.
1. Select the desired tone quality. (See pages 42-44.)
2. Follow the procedure of "Making a recording from radio broad-
casts" on page 30.
When playing back such recordings, press ON/FLAT on the tuner/
sound processor to set to "FLAT".
To record without any tonal effect
Press ON/FLAT on the tuner/sound processor to set to "FLAT".
(See pages 42 and 43.)
31
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SC-CH515 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SC-CH515 in the language / languages: English as an attachment in your email.

The manual is 6,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info