637111

Technics SC-CH515 Manual

27
Zoom out
Zoom in
Previous page
1/60
Next page
! I
To find the beginning of a program
(TPS: tape program sensor)
Press <1<1(TPS) or (TPS) I_1_ while the tape is
playing.
If the forward side (D) is playing:
[ (TPS)II,4_ I : The tape will play from the beginning of the next
tune.
I .,_TPs) J : The tape will rewind to the beginning of the present
tune. Then the tune will play again.
If the reverse side (<]) of the tape is playing:
The reverse operation should take place.
TPS (Tape Program Sensor) is the function that searches for the
silent passage in a tape program. So, it may sometimes fail to
operate correctly in the following situations:
eWhen there is no blank space between tape programs (for exam-
ple, when you are playing a tape recorded from a microphone)
eWhen the interval between programs (blank space) is less than
4 seconds
oWhen there is a particular low-level passage or silent passage in
the middle of a program (For example, classical music)
oWhen the program is less than 10 seconds, or when it is less than
10 seconds from the beginning of the program to the beginning of
the next program
oWhen a tape has been recorded with fade-ins (the function that
increases the volume level gradually at the beginning of a program)
and fade-outs (the function that decreases the volume level grad-
ually at the end of a program)
-Avt_r_
For your reference:
Each decks' play direction is stored in the system's memory. So the
play direction may change when you press DECK 1/2.
To fast forward or rewind the tape
Press <1<1(TPS) or (TPS) I_1_ while the tape is in
the stop mode.
If the forward side (1:>)of the tape is playing:
: The tape will be fast forwarded.
: The tape will be rewound.
If the reverse side (<3) of the tape is playing:
The reverse operation will take place.
High-speed rewind/fast-forward:
On this unit, if there is less tape on the take-up side than on the
supp}y side (refer to the illustration below) at the time that 4<1 or
I_b,. is pressed, the speed of the rewind/fast-forward operation will
automatically be increased for approximately 1.5 times the normal
speed. This function makes it possible to wind the tape faster when
there is a large amount of tape to be wound.
Tape
Take up side
;upply side
• When there is more tape on the take up side than on the supply
side, the tape will be wound at the normal speed.
olf high speed winding is begun from a state in which the tape is
partly wound, such as that shown in the illustration above (for
example, when the ratio of tape between the two sides is 1:3), high
speed winding will continue until the ratio between the two sides
reaches 3:1, and then the remaining winding will be done at the
normal speed.
For your reference:
You can fast forward or rewind the tape while you are playing or
recording a tape in another deck. Press DECK 1/2 to switch to the
non playing deck, and then press 4<1 or IH_.
After above operation, be sure to press DECK 1/2 to select the deck
in which you are playing a tape.
27
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SC-CH515 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SC-CH515 in the language / languages: English as an attachment in your email.

The manual is 6,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info