637111
9
Zoom out
Zoom in
Previous page
1/60
Next page
_ _ !i!_ _!_, !_ _!!_i!! i_ _!_!_!i__!_i_i !!i!,z!!! __ i!!_i_i!!_!!!!i_!_!__!i!_z_i!!_!!!!!!!_i!¸i_i_i!_!_!ii_ii!!!!_!i!!i!_i_i!!i!!!!_!!i!iiiiiii_!_!!iiii_i_!!!!_!iiii!_!_!_iiiiiiii_!_!!iiiiiiii_!!i!iiiii!_!_!iii!ii!iii_ii!i!i!i!i!i_iz!_i!!i!i!_ _:_ __:_____z_:_ __ __ _ _ __ ___ _ _ _ __ __ __ _¸_i_iiiii_i__z_i_iiiiiii!iiiii_ii_iiiiiii_i_i_iii_iii_i_i_i_iiii_i_i_iiii_i_i_i_i_i_i_iiiiiiiiii_i_i_iil
_iiiiiii_iiiii_iiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiii_iiiiii_iiiiiiiiiiiiiii_iiii_i iiiiii!iiiiiiiiiiiiii_!iiiii!iiiii!ii!iiiiiii!iiiiiii_ iiiiii_iiiii_iiiii_iiiii_iiii_ii i_ iiii_iii _iii_ii_iiii_ii _ii_ i i_i ii_ i_iiiil _iiii_iii_i_i_i_i_i_i_ii_i_i_iii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ _i_'_'_ _'__i_'_'_'_ _ii_
Connect the AM loop antenna. /,_ Connect the right (R) and left (L) speaker
1. Attach the antenna holder to the rear panel of the "7' cables.
tuner/sound processor.
2. Clamp the AM loop antenna to the antenna holder and
connect the antenna terminal to the rear panel of the
tuner/sound processor.
3. Position the loop for the best reception.
Antenna holder
Press in until you hear a click.
AM loop antenna
Press hard enough to get it
fixed firmly in the place,
with a click.
You may attach the AM antenna holder with a screw (in-
cluded) to a rack or other structure. In this case, attach as
shown in _
-- -- Rack or other structure
To minimize noise pickup, keep the AM loop antenna cord
along the heat outlet grille, and away from the flat cables.
Be sure to connect speaker cables before connecting the
AC power supply cord.
eThe load impedance of any speaker used with this unit must
be 6-8£_.
Match the two wires from the left and right speaker cables
with the same colored levers of the speaker terminals, then
insert the wires into the respective terminals.
1. Strip off the outer
covering, and twist =_====,, _),
the center conductor. 15mm
2.
Make sure the bare ends of the wires are not unravelled.
(If they are, twist them tight again.) I'_
(For SC-CH717) I I_--_]
Insert the wire to the rear panel .._11_ I _
of the speakers, and then pull _ I
down the lever. _ "'J
(For SC-CH515)
Q Tilt the lever back
and insert the wire.
(_ Close the lever and
pull the cord gently
to be sure that it is
secured.
3. Insert the wire to the
rear panel of the
amplifier, and close the lever.
To prevent damage to circuitry, J,_F_ t
never short-circuit positive (+)
and negative (-) speaker wires.
Be sure to connect only positive (red) wires to positive (+)
terminals and negative (black) wires to negative (-) ter-
minals.
(For SC-CH717 only)
Connect the surround speaker cord.
Rear panel of Rear panel of
the amplifier the speakers
Connect the AC power supply cord after you
have connected all other cables.
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Technics SC-CH515 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Technics SC-CH515 in the language / languages: English as an attachment in your email.

The manual is 6,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info