Manual Team SIS 8 (page 12 of 40) (English, German, Dutch, French, Italian, Portuguese, Spanish)

487284

Zoom out

Zoom in

1/40



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don‟t change

the page numbering. Keep the language integrity.

12 TEAM SIS 8 - 070426

Assembly page 12/40

Fax +32 2 359 95 50

fabrics according to ironing temperature: wool with wool, cotton with cotton, etc. The iron

heats up quicker than it cools down. Therefore, start ironing the articles requiring the

lowest temperature such as those made of synthetic fibres. Then progress to the higher

temperatures.

 If the article is made of a mixture of different fibres, you must always select the lowest

ironing temperature of the composition of those fibres (E.g. an article consisting of 60%

polyester and 40% cotton should be ironed at the temperature indicated for polyester and

without steam).

If you do not know what kind of fabric(s) the article has been made of, find a spot,

which will be invisible when wearing or using the article to try out the ironing temperature.

(Always start at a low temperature and increase to one, which gives the required results).

 Pure woollen fabrics (100% wool) may be pressed with the iron set to a steam position. It is

recommended to apply shot-of-steam and use a dry pressing cloth.

 When steam-ironing woollen fabrics, shining of the fabric may occur. This can be

prevented by turning the article inside out and ironing the inside or by interposing a light

damp cloth.

 Velvet and other textures that rapidly acquire shiny spots should be ironed in one direction

only (with the nap), applying only light pressure. Always keep the iron moving.

 Iron the reverse side of synthetic materials and silk, it is not advisable to use steam as this

may cause stains.

FILLING WITH WATER (FOR STEAM-IRONING)

 Make sure the appliance is unplugged.

 Put the switch of the water tank (2) in off position (0).

 Position the base of the appliance on a stable flat surface and unscrew the cap by

simultaneously pressing it down and turning it anticlockwise (if you left water in the tank

and the cap screwed, a light degazing will happen during the next use. It‟s normal and

presents no danger).

 Use the funnel to fill the steam tank with water (max. 500 ml).

 You can use tap water, however, if the water is very hard, it is advisable to use distilled

water.

 Never use vinegar, descaling agents or other chemicals.

 Close the steam tank by turning the screw cap clockwise (see page 4).

FILLING WITH WATER WHILE IRONING

CAUTION: WHEN THE APPLIANCE IS IN OPERATION, THE STEAM TANK WILL BE UNDER PRESSURE

WITH HOT STEAM.

FIRST OF ALL BE SURE THAT THERE IS NO MORE STEAM IN THE WATER TANK. THE BASE AND THE

IRON STILL BEING PLUGGED IN, BLEED THE TANK BY PUSHING THE BUTTON (3) UNTIL NO MORE

STEAM ESCAPES, THEN SWITCH OFF THE BASE (SWITCH 2 IN OFF-POSITION (0)) AND UNPLUG THE

APPLIANCE. CAREFULLY UNSCREW THE CAP IN ORDER TO CHECK IF THERE IS NO MORE STEAM

AND THEN UNSCREW IT COMPLETELY. LET THE TANK COOL DOWN A FEW MINUTES AND THE FILL IT

AGAIN. CAUTION: IF YOU FILL IT TOO EARLY, STEAM OR HOT WATER WILL ESCAPE FROM THE

OPENING. WE ADVISE YOU TO PROCEED SLOWLY WHEN YOU FILL IN ESPECIALLY AT THE

BEGINNING. FINALLY CLOSE THE WATER TANK WITH THE CAP. YOUR APPLIANCE IS READY TO

OPERATE.

STEAM IRONING

 Fill the water tank with water and insert the mains plug into a wall socket.

 As indicated on the temperature dial (1) and the table, steam ironing is only possible at

higher ironing temperatures, so set the dial to  or .

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Team SIS 8 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Team SIS 8 Manual

Product: