487100

Team KR 2 Manual

16
Zoom out
Zoom in
Previous page
1/38
Next page
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
16
Assembly page 16/38
Fax +32 2 359 95 50
UK STYLE PLUG WIRING INSTRUCTIONS (IN THE UK ONLY)
This product must only be used from a 13 amp power socket. If a BS1363 approved 13 amp plug is
used, it should be fitted with a 13 amp fuse. The wires on the power cord are colour coded:
blue = neutral, brown = live, green or green & yellow = earth.
The blue wire must be connected to the terminal marked N or coloured in black.
The brown wire must be connected to the terminal marked L or coloured in red.
The green (& yellow) wire must be connected to the terminal marked E or coloured in green (& yellow).
IMPORTANT INFORMATION
This appliance is not for professional use. You should follow the requested breaks. Failure to follow
this instruction carefully may result in damage to the motor. Please refer to the rating label for the
maximum continuous usage time (KB xx min where xx is the maximum usage time). The breaks
should last at least 10 minutes.
USE AND FUNCTIONS
Use
Place the processor bowl (9) onto the bowl shaft (2).
Make sure the three tips around the bowl shaft are inserted into the three slots on the bottom of
the processor bowl.
The bowl lid with funnel (8) must be locked into the bowl lid locking slot (1).
Connect the appliance.
Turn the ON/OFF & speed control switch (4) either to “I” (slow speed) or to “II” (fast speed),
depending on the preparation you make.
You can also use the pulse button (6) but only if you turn the ON/OFF speed control switch to
“0”. Press this button to use the appliance punctually. A light press will make the motor work
slowly, while a heavy press will make it work faster.
You can also use the auto clean button (5) but only if you turn the ON/OFF speed control switch
to “0”. With this function, the motor will only work slowly. This button is used to clean the
blender bowl (see the section «Cleaning»).
Depending on the type of usage, different accessories should be used, according to the below
instructions.
Grating / Slicing
Unplug the appliance.
Place the processor bowl onto the bowl shaft. Make sure the three tips around the bowl shaft are
inserted into the three slots on the bottom of the processor bowl.
For grating, insert the spindle (10) into the center of the reversible grating/slicing disk (10), with
the grating blade (12) side facing the lid with funnel. For that the three tips around the spindle have
to penetrate the three slots around the center of the disk. Then rotate the disk anti-clockwise by
gripping the spindle as shown in the figure and go as far as it can in order to lock it into the disk.
For slicing, the slicing blade (13) side must be facing the lid with funnel (8).
Once mounted, place the disk on the bowl shaft and add the lid with funnel as described in the
section «Use».
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team KR 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team KR 2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info