486998

Team HC 9 Manual

11
Zoom out
Zoom in
Previous page
1/35
Next page
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
11
Assembly page 11/35
Fax +32 2 359 95 50
maximum continuous usage time (KB xx min where xx is the maximum usage time). The breaks
should last at least 10 minutes.
UK STYLE PLUG WIRING INSTRUCTIONS (IN THE UK ONLY)
This product must only be used from a 13 amp power socket. If a BS1363 approved 13 amp plug is
used, it should be fitted with a 13 amp fuse. The wires on the power cord are colour coded:
blue = neutral, brown = live, green or green & yellow = earth.
The blue wire must be connected to the terminal marked N or coloured in black.
The brown wire must be connected to the terminal marked L or coloured in red.
The green (& yellow) wire must be connected to the terminal marked E or coloured in green (&
yellow).
BEFORE YOU BEGIN
Make sure that your clipper is clean, properly oiled and in perfect working condition.
Place a towel around the neck of the person whose hair is to be cut to prevent hair from falling
inside the collar.
Have the person sit on a chair so that his/her head is at your eye’s level.
Comb the hair thoroughly and hold the clipper in a relaxed, comfortable grip. This will help you
maintain an accurate cutting control.
CUTTING HAIR WITH THE ATTACHMENT COMBS
To attach comb, hold it with teeth up and snap comb attachment firmly to the bottom of the clipper
blade (see picture 1):
Attachment comb #1...leaves hair approx. 1/8" in length
Attachment comb #2...leaves hair approx. 1/4" in length
Attachment comb #3...leaves hair approx. 3/8" in length
Attachment comb #4...leaves hair approx. 1/2" in length
Only cut a small amount of hair to start with until you become accustomed to the length each
attachment comb gives to the hair.
We suggest you try the longest attachment comb on the clipper first, then use the shorter one if
the desired length is shorter.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The clipper
works most efficiently when it works at its own speed.
Start by combing the hair in its natural direction.
Attach the largest attachment comb to your clipper and start by trimming the sides from the
bottom upwards. Hold the clipper lightly against the hair with the comb teeth pointing up but flat
against the head. Slowly lift the clipper up and outward through the hair, cutting only a small
amount at a time (2+3).
If you want shorter hair, either change to a lower numbered attachment comb or apply more
pressure to the present attachment comb. This procedure requires practice, and it is always better
to leave too much hair during the first few haircuts (4).
For the top of the head, you will give a fairly short cut if you use the attachment comb #1. With
the teeth flat against the head, slowly start trimming from the front to the back. Again, it is better
to leave the hair longer at the beginning (5).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 9 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info