487003

Team HC 18N Manual

9
Zoom out
Zoom in
Previous page
1/40
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity.
9 TEAM HC 18 N - 091014
Assembly page 9/40
Fax +32 2 359 95 50
cover facing the head), the top of the blades perpendicular to the skin and cut to the
desired length (7). If necessary, insist on the reluctant hair.
When you get used to your hair clipper, you will be able to make layers simply by
changing the length of the combs in function of the cutting zone. These handling asks for
a special dexterity in order to obtain a correct result.
SHORT CUTS
Always cut from the back of the neck to the crown, using the longest attachment comb.
Holding it flat against the head, slowly move the clipper up through the hair. Use the same
technique for the sides.
For the front of the crown, cut the hair against the direction in which it grows. Then even it
up with the sides.
For a flat top, use a flat comb, not the attachment comb. Just cut hair on top of the head
over it. To taper hair down to the neckline, use closer cutting attachment combs. Comb
hair, check for uneven spots and outline sideburns and neckline.
The four basic areas illustrated are your "road map" to easy do-it-yourself hair cutting (8).
LEVER
This lever has two main functions:
Regulation of the cutting length because in the position short hair (lever pushed to the
front side) you can cut the length of the used combs or make outlining by pulling it to the
backside, you can make the cutting length longer (this allows middle cutting lengths
above the 4 delivered combs).
Partial cleaning of the blades when in use by to and fro motions in order to remove the
hair blocked in the blades.
MAINTENANCE
Your clipper was carefully examined before leaving our factory to ensure that the blades
were oiled and aligned.
Blades must be realigned if they have been removed for cleaning or replacement.
Therefore, as the lever is pushed to the front side in short hair position, the end of the top
blade teeth is approximately 1.2 mm away from bottom blade. Compare your clipper
blades with the sketch (9).
If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for
a few moments, turn off and unplug. Loosen screws slightly and turn the upper blade until
a correct alignment. Then tighten screws once the blades are aligned (10).
Change the blades as soon as they become blunt.
To clean the blades, use the small brush delivered with your appliance and if necessary,
remove them completely.
OIL
To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).
Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will
evaporate and leave the thick oil which may slow down the blades' motion.
ACCESSORIES
Your appliance is delivered with a complete set of hair accessories, which allows you to make
the desired hair cuttings: 1pair of scissors, 1 comb and 4 interchangeable combs to place on
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 18N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 18N in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info