487003

Team HC 18N Manual

8
Zoom out
Zoom in
Previous page
1/40
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity.
8 TEAM HC 18 N - 091014
Assembly page 8/40
Fax +32 2 359 95 50
IMPORTANT INFORMATION
This appliance is not for professional use. You should follow the requested breaks. Failure to
follow this instruction carefully may result in damage to the appliance. Please refer to the rating
label for the maximum continuous usage time (KB xx min where xx is the maximum usage time).
The breaks should last at least 10 minutes.
BEFORE YOU START
Make sure that your clipper is clean, properly oiled and in perfect working condition.
Attention, if the blades are not properly oiled, your appliance will not work correctly.
Place a towel around the neck of the person whose hair is to be cut to prevent hair from
falling inside the collar.
Have the person sit on a chair so that his/her head is at your eye’s level.
Comb the hair thoroughly and hold the clipper in a relaxed, comfortable grip. This will help
you maintain an accurate cutting control.
CUTTING HAIR WITH THE ATTACHMENT COMBS
To attach the comb, hold it with teeth up and snap comb attachment firmly to the bottom of
the clipper blade (see picture 1):
Attachment comb #0.5...leaves hair approx. 1/8" in length
Attachment comb #1...leaves hair approx. 1/4" in length
Attachment comb #3...leaves hair approx. 3/8" in length
Attachment comb #4...leaves hair approx. 1/2" in length
In order to become accustomed to the length of each attachment comb we
recommend for the first use to place the attachment comb #4 and then to reduce the
length steadily until you obtain the desired length. Afterwards, you can place directly the
comb you want.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The
clipper works most efficiently when it works at its own speed.
Once you placed the attachment comb on the hair clipper, cut the hair by placing the
comb teeth flat against the scalp (2). We recommend to proceed by small lengths in
order to avoid stuffing. Therefore you only have to remove the comb regularly by bending
it lightly outward. Then make the same movement but start lower than the point you
remove the clipper in order to obtain a homogeneous length.
The cutting always happens by moving towards in the opposite side of the natural
direction of the hair. For the backside, start from the nape of the neck and go to the top
of the head (3), for the sides, from the ears to the top of the head (4) and for the top of
the head, from the forehead to the backside of the head (5).
We recommend to do the hair regularly in order to check the homogeneity of the cutting
and to replace the hair. For the same reason, once the hair is cut and done, work the hair
clipper again but quicker in order to cut the hair that would have escaped from the first
cutting. You can eventually insist on the places with defaults.
OUTLINING
Outlining requires no attachment combs. Take the clipper and push the lever (see next
paragraph) up to the close-cut position.
Comb hair into the required style. Start from the outline of the ear by placing the side of
the hair clipper on the skin and following the roundness of the ear (6). To draw the
sideburns and the nape of the neck, place the hair clipper in the wrong side (with the
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 18N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 18N in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info