487002

Team HC 15 Manual

10
Zoom out
Zoom in
Previous page
1/35
Next page
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
10
Assembly page 10/35
Fax +32 2 359 95 50
OUTLINING
Outlining requires no attachment combs. Take the clipper and push the lever (see next
paragraph) up to the close-cut position.
Comb hair into the required style. Start from the outline of the ear by placing the side of the hair
clipper on the skin and following the roundness of the ear (6). To draw the sideburns and the
nape of the neck, place the hair clipper in the wrong side (with the cover facing the head), the top
of the blades perpendicular to the skin and cut to the desired length (7). If necessary, insist on the
reluctant hair.
When you get used to your hair clipper, you will be able to make layers simply by changing the
length of the combs in function of the cutting zone. This handling ask for a special dexterity in
order to obtain a correct result.
LEVER
This lever has two main functions:
Regulation of the cutting length because in the position short hair (lever pushed to the front side)
you can cut the length of the used combs or make outlining by pulling it to the backside, you can
make the cutting length longer (this allows middle cutting lengths above the 4 delivered combs).
Partial cleaning of the blades when in use by to and fro motions in order to remove the hair
blocked in the blades.
ADJUSTABLE LEVER
Your clipper was carefully examined before leaving our factory to ensure that the blades were
oiled and aligned.
Blades must be realigned if they have been removed for cleaning or replacement. Therefore, as
the lever is pushed to the front side in short hair position, the end of the top blade teeth is
approximately 1.2 mm away from bottom blade. Compare your clipper blades with the sketch
(9).
If the blade alignment is incorrect, add a few drops of oil to the blades, turn clipper on for a few
moments, turn off and unplug. Loosen screws slightly and turn the upper blade until a correct
alignment. Then tighten screws once the blades are aligned (10).
Change the blades as soon as they become blunt.
To clean the blades, use the small brush delivered with your appliance and if necessary, remove
them completely.
OIL
To maintain your clipper in peak condition, the blades should be oiled every few haircuts (12).
Do not use hair oil, grease or oil mixed with kerosene or any solvent, as the solvent will
evaporate and leave the thick oil which may slow down the blades' motion.
POWER SCREW
The power screw allows you to adjust the power. It has been adjusted before leaving the factory;
however, if the voltage in your home is low, you may need to re-adjust it. To adjust, use a
screwdriver or a thin coin to turn power screw clockwise until it stops (13). Then slowly turn
power screw out (counter-clockwise) until noise reduces. This is the maximum power setting.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 15 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info