487002

Team HC 15 Manual

8
Zoom out
Zoom in
Previous page
1/35
Next page
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
8
Assembly page 8/35
Fax +32 2 359 95 50
IMPORTANT INFORMATION
This appliance is not for professional use. You should follow the requested breaks. Failure to follow
this instruction carefully may result in damage to the appliance. Please refer to the rating label for the
maximum continuous usage time (KB xx min where xx is the maximum usage time). The breaks
should last at least 10 minutes.
UK STYLE PLUG WIRING INSTRUCTIONS (IN THE UK ONLY)
This product must only be used from a 13 amp power socket. If a BS1363 approved 13 amp plug is
used, it should be fitted with a 13 amp fuse. The wires on the power cord are colour coded:
blue = neutral, brown = live, green or green & yellow = earth.
The blue wire must be connected to the terminal marked N or coloured in black.
The brown wire must be connected to the terminal marked L or coloured in red.
If in doubt, contact a qualified electrical engineer.
BEFORE YOU BEGIN
Make sure that your clipper is clean, properly oiled and in perfect working condition. Attention,
if the blades are not properly oiled, your appliance will not work correctly.
Place a towel around the neck of the person whose hair is to be cut to prevent hair from falling
inside the collar.
Have the person sit on a chair so that his/her head is at your eye’s level.
Comb the hair thoroughly and hold the clipper in a relaxed, comfortable grip. This will help you
maintain an accurate cutting control.
CUTTING HAIR WITH THE ATTACHMENT COMBS
To attach comb, hold it with teeth up and snap comb attachment firmly to the bottom of the clipper
blade (see picture 1):
Attachment comb #1...leaves hair approx. 1/8" in length
Attachment comb #2...leaves hair approx. 1/4" in length
Attachment comb #3...leaves hair approx. 3/8" in length
Attachment comb #4...leaves hair approx. 1/2" in length
In order to become accustomed to the length of each attachment comb we recommend for the
first use to place the attachment comb #4 en then to reduce the length steadily until you obtain
the desired length. Afterwards, you can place directly the comb you want.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The clipper
works most efficiently when it works at its own speed.
Once you placed the attachment comb on the hair clipper, cut the hair by placing the comb teeth
flat against the scalp (2). We recommend to proceed by small lengths in order to avoid stuffing.
Therefore you only have to remove the comb regularly by bending it lightly outward. Then make
the same movement but start lower than the point you remove the clipper in order to obtain an
homogeneous length.
The cutting always happens by moving towards in the opposite side of the natural direction of
the hair. For the backside, start from the nape of the neck and go to the top of the head (3), for
the sides, from the ears to the top of the head (4) and for the top of the head, from the forehead to
the backside of the head (5).
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 15 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info