486999

Team HC 12 Manual

11
Zoom out
Zoom in
Previous page
1/38
Next page
Generated by Unregistered Batch DOC TO PDF Converter
2011.3.804.1511, please register!
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International
BELGIUM. The page must reproduced and folded in order to
obtain a mini booklet B5 (+/- 150 mm width x 210 mm height).
The page must be folded in order to keep the good numbering
when you turn the page of the I/B . Don’t change the page
numbering. Keep the languages integrity.
11
Assembly page 11/38
Fax +32 2 359 95 50
To attach comb, hold it with teeth up and snap comb attachment firmly to the appliance:
Attachment comb A...leaves hair approx. 1/6", 1/3", 1/2", 2/3" and 5/6" in length
Attachment comb B...leaves hair approx. 1", 1 1/6", 1 1/3", 1 1/2" and 1 2/3" in length
CUTTING HAIR WITH THE ATTACHMENT COMBS (see Page 3: )
Only cut a small amount of hair to start with until you become accustomed to the length each
attachment comb gives to the hair.
We suggest you try the longest attachment comb B on the clipper first.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The clipper
works most efficiently when it works at its own speed.
Start by combing the hair in its natural direction.
Attach the attachment comb B to your clipper and start by trimming the sides from the bottom
upwards. Hold the clipper lightly against the hair with the comb teeth pointing up but flat against
the head. Slowly lift the clipper up and outward through the hair, cutting only a small amount at
a time and .
If you want shorter hair, either change to the comb A or change the hair length (see - ). You
can also apply more pressure to the present attachment comb. This procedure requires practice,
and it is always better to leave too much hair during the first few haircuts .
For the top of the head, you will give a fairly short cut if you use the attachment comb A. With
the teeth flat against the head, slowly start trimming from the front to the back. Again, it is better
to leave the hair longer at the beginning .
Outlining
Outlining requires no attachments.
Comb hair into the required style. Position clipper between the sideburns and the ear. Make sure
the outer edge of the blade is against the hairline. With the outline of the hair as your guide,
slowly move the clipper around the ears . For the back of the neck and the sideburns, hold the
clipper upside down , and move downwards holding it against the skin at the length desired.
Short cuts
Always cut from the back of the neck to the crown, using the attachment comb B. Holding it flat
against the head, slowly move the clipper up through the hair. Use the same technique for the
sides, cutting from the bottom to the upper side of the head .
For the front of the crown, cut the hair against the direction in which it grows. Then even it up
with the sides .
To taper hair down to the neckline, use attachment comb A. Comb hair, check for uneven spots
and outline sideburns and neckline .
MAINTENANCE
Your clipper was carefully examined before leaving our factory to ensure that the blades were
oiled and aligned. To maintain your clipper in peak condition, the blades should be oiled every
few haircuts.
Use the small brush to remove remaining hair.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Team HC 12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Team HC 12 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info