617918
42
Zoom out
Zoom in
Previous page
1/84
Next page
42 TASCAM SS-CDR200/SS-R200/SS-R100
3 Select
OTHERS
.
4 Press the MULTI JOG dial or , [LOCK] button (or
remote control ENTER or t button) to open the
REC OTHERS
screen.
5 Select
SRC
.
6 Press the MULTI JOG dial or , [LOCK] button (or
remote control ENTER or t button) to move the
cursor right to select the value.
7 Turn the MULTI JOG dial (or press the remote
control 5 and b buttons) to set it to
ON
(default
value:
OFF
).
8 When you have finished making the setting, press
the HOME/DISPLAY button (or remote control
HOME/DISP button) to return to the Home Screen.
NOTE
If a digital signal with a sampling frequency that
differs from the sampling frequency specified in the
REC FORMAT
item is being received at the DIGITAL
IN jack, and you attempt to record with
SRC
off, an
FS
UNMATCH
error message will appear.
The sampling rate converter (SRC) setting is retained
even after the power is turned OFF.
Monitoring the input signal
When you press the front panel or remote control
RECORD button to enter recording standby, the RECORD
and READY buttons light, and the input signal will be
output from the various output jacks (headphones, analog
balanced, analog unbalanced and digital). In addition, the
meters on the home screen will show the input level.
To end recording standby, press the front panel or remote
control STOP button.
TIP
If you simply want to monitor the input signal without
intending to record anything, press the RECORD key
without any media in the current device.
MONITOR
will
appear on the display, and the RECORD button will
blink red.
To stop monitoring the input signal, press the STOP
button on the front panel or remote control.
Adjusting the input signal level and
balance
You can use the menu to adjust the level and balance of
the input signal.
Follow the instructions in the “Monitoring the input
signal” section above to enable monitoring of the input
signal, and then follow these procedures.
1 Press the MENU [JOG] button (or remote control
MENU button) to open the
MENU
screen.
2 Open the
REC
menu.
3 Select
INPUT VOLUME
.
4 Press the MULTI JOG dial or , [LOCK] button (or
remote control ENTER or t button) to open a pop-
up with the
INPUT VOLUME
settings.
5 Set the following
INPUT VOLUME
items.
LEVEL
Adjust the input level.
Options:
–inf
,
54dB
0.0dB
(default value) –
+18dB
BALANCE
Adjust the input balance.
Options:
L50
C
(center, default value) –
R50
NOTE
The level meter will show
OVER
at
0.2 dBfs
.
Since the level meter appears on the Home Screen at
the top of the display, you can check the input level as
you adjust it. Set the level as high as possible without
making the
OVER
indicator to the right of the meter
appear.
6 When you have finished making the setting, press
the HOME/DISPLAY button (or remote control
HOME/DISP button) to return to the Home Screen.
NOTE
The input
LEVEL
and
BALANCE
settings are retained even
after the power is turned OFF.
Basic recording operations
You can begin recording after you have finished making
the above settings (input source selection, recording file
format setting, sampling rate converter ON/OFF, input
level adjustment).
To start recording standby from a stopped state:
Press the front panel or remote control RECORD button
to put the unit in recording standby (The RECORD and
READY buttons light).
To start recording from recording standby:
Press the front panel or remote control PLAY button.
To switch from recording to recording standby:
Press the front panel or remote control READY button.
5 – Recording
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam SS-CDR100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam SS-CDR100 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info