617905

Tascam HS-8 Manual

9
Zoom out
Zoom in
Previous page
1/72
Next page
TASCAM HS-8 9
Press this key while recording to put the unit in
recording standby. Both the PAUSE and REC keys light
during recording standby.
w REC key/indicator
When a recordable CF card is installed and the unit is
stopped, press this key to put the unit into recording
standby. Both the PAUSE and REC keys light during
recording standby.
Press this key while recording to stop recording the
current file, and continue recording to a new file.
CAUTION
If you press the REC key less than 4 seconds after beginning
•
recording, the unit will not start recording a new take.
Depending on the folder setting for mono recording les, the
required time could be even longer. (See “Folder where les are
saved in mono mode” on page 33.)
Depending on other conditions, recording of a new take
•
might not be possible when the REC button is pressed during
recording. (See “Recording operation limitations” on page 29.)
Recording is not possible if any of the following conditions
•
apply. Change the recording folder.
The folder contains 999 takes
•
The number at the end of the take name has reached 999
•
The remaining recording time indicator on the Home Screen
•
shows “Rec Limit”. (See “Recording operation limitations” on
page 29.)
e JOG/SHUTTLE dial
When in jog operation mode, turn this to change the
playback position by a corresponding amount.
When in shuttle operation mode, turn this to adjust
the playback speed according to the degree of rotation.
If you return to the original position when in shuttle
operation mode, the transport status is restored to
how it was before shuttle playback was begun.
r PHONES knob/jack
Connect stereo headphones to this standard stereo
phone jack. Use the PHONES knob to adjust the
headphones output level.
CAUTION
Before connecting headphones, turn the PHONES knob to the
minimum volume. Failure to do so could cause sudden loud noises
to occur, which might damage your hearing or equipment.
t KEYBOARD connector
Connect an IBM PC-compatible keyboard with a
PS/2 interface, and use it to input project, folder, and
channel names, for example. By default, the unit is set
to use a US keyboard. To use a Japanese keyboard,
since the key allocation is different, change the setting
on the
PREFERENCES
page of the
SYSTEM
SETUP
screen.
(See “PREFERENCES page” on page 52.)
y PROJECT key
Press to open the
PROJECT
screen. (See “PROJECT
screen overview” on page 33.)
u EXIT/CANCEL (PEAK CLEAR) key
Press to cancel input or item selection. On the Home
Screen, this functions as a reset button for peak hold
marks shown on the level meters.
When the
MENU
screen or
PROJECT
screen is open,
press this to return to the Home Screen. On other
screens, press this to return to the previous screen.
When a pop-up window is open, press this to cancel
an operation.
i CALL (CHASE) key
Press to locate the call point, which is where playback
last started from playback standby, and resume
playback standby.
Press this key while pressing the SHIFT key to turn
synchronization with external timecode ON/OFF.
o LCD TILT button
Press this button to unlock the color display, so that
you can adjust its angle by pulling the bottom of the
display outward.
To put the display away, press this button to unlock it
and push the bottom inward.
p Ô ( )/ ( ) (search) keys
Use these keys to search.
Ô ( ): Search backward
( ): Search forward
Press one of these keys while pressing the SHIFT key
to search at high speed
a Â/¯ (MARK Â/¯) (SKIP) keys
Use these to skip to the previous/next take.
Press these keys while pressing the SHIFT key to move
to the previous/next mark. After moving, the same
playback state resumes (stopped/standby/playback).
s MARK key
Press this key to add a mark at the currently located
time. The maximum number of marks, including
automatic marks, possible in a single file (take) is 99.
(See “Mark functions” on page 55.)
d SHIFT key
When stopped/in playback standby/during playback:
Press the
•
 while pressing and holding this key
to move to the previous mark, and resume the same
playback state.
Press the
•
¯ key while pressing and holding this
key to move to the next mark, and resume the same
playback state.
Press a
•
Ô ( )/( ) key while pressing
and holding this key to search at high speed.
Press the
•
JOG (SHUTTLE) key while pressing and
holding this key to activate the shuttle operation
mode.
Press the
•
STOP (RETAKE) key while pressing and
holding this key to retake the recording (erasing the
last recorded take).
2 − Names and functions of parts
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-8 in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info