617903
14
Zoom out
Zoom in
Previous page
1/152
Next page
14
TASCAM HS-4000
2 − Names and functions of parts
color display might flicker or noise might be heard when
monitoring.
If this occurs, use the GROUND terminal. (Please prepare a
wire to use with the GROUND terminal.)
PARALLEL connector
The PARALLEL connector on the rear panel allows external
control of this unit.
The pin assignments are as follows.
Pin
No.
Timeline / Take /
Playlist [Single] /
On Air
Playlist [Dual, A/B
MIXED]
TASCAM
RC-SS20
PonMode
I/O
1 GND GND GND
2 PLAY PLAY A FLASH 1 I
3 STOP STOP A FLASH 2 I
4 RECORD (Reserved) FLASH 3 I
5 SKIP FWD SKIP FWD FLASH 4 I
6 SKIP BWD SKIP BWD FLASH 5 I
7 (Reserved) STOP B STOP I
8 FADER START FADER_START A FADER_START I
9 TALLY_BC_STOP TALLY_PAUSE B TALLY_BC_STOP O
10
TALLY_PAUSE
/ TALLY_BC_
PAUSE
TALLY_PAUSE A
TALLY_PAUSE
A / TALLY_BC_
PAUSE
O
11 TALLY_RECORD (Reserved) RESERVED O
12 TALLY_STOP TALLY_STOP A TALLY_STOP O
13 TALLY_PLAY TALLY_PLAY A TALLY_PLAY O
14
REMOTE_
SELECT,
H or Open
REMOTE_SELECT,
H or Open
REMOTE_
SELECT, L
I
15 PAUSE PAUSE FLASH 6 I
16 (Reserved) PLAY B FLASH 7 I
17 AUX1, FF AUX1, FF FLASH 8 I
18 AUX2, REW AUX2, REW FLASH 9 I
19 AUX3, MARK AUX3, MARK FLASH 10 I
20 (Reserved) A/B SELECT FLASH_PAGE I
21
TALLY_BC_
STANDBY
TALLY_PLAY B
TALLY_BC_
STANDBY
O
22
TALLY_CF1 /
TALLY_BC_CM
TALLY_STOP B
TALLY_CF1 /
TALLY_BC_CM
*1
O
23 TALLY_ONLIN TALLY_ONLINE A TALLY_ONLINE O
24
TALLY_CF2 /
TALLY_BC_END
TALLY_ONLINE B
TALLY_CF2 /
TALLY_BC_END
*2
O
25 +5V *3 +5V *3 +5V *3
I: Command input for transport control
Internal circuit, +5V pull-up
Operates with low commands of 50 msec or more
O: Command output, for tally output
The internal circuit is open collector (10Ω output
impedance)
Low command output when operating
20 V dielectric strength, 35 mA maximum current
*1: With an RC-SS20, this is assigned to the CF.
*2: With an RC-SS20, this is assigned to the CD indicator.
*3: 50 mA maximum supplied current
When REMOTE Select (pin 14) is set to high, it functions
according to the operation mode and can be used as an
ordinary parallel controller.
When set to low, flash start mode is enabled. In addition,
depending on the high/low setting of the Flash Page (pin 20),
the key assignments are as follows.
Pin 14 Pin 20 Flash start take
Low High 1-10
Low Low 11-20
tally_BC_xxx: Use the menu setting to turn output ON or OFF.
(When connected to a TASCAM RC-SS20, set output to OFF.)
tally_BC_STOP/CM/END: 250msec pulse output
tally_BC_STANDBY/PAUSE: level output
When this unit is set to dual or A/B MIXED playlist mode and
REMOTE Select (pin 14) is set to high (dual or A/B MIXED
Playlist), use pin 20 (A/B SELECT) to select player A/B (Hi is player
A, Lo is player B).
The following pins affect the selected player.
Pin 5 SKIP FWD
Pin 6 SKIP BWD
Pin 15 PAUSE
Pin 17 AUX1
Pin 18 AUX2
Pin 19 AUX3
The following example is of a connection that uses a fader to
start and stop playback of this device.
For details about the AUX 1-3 (pins 17-19) function assignments,
see“PARALLEL page” on page 107.
NOTE
When controlling this unit with an external device that
is connected to the PARALLEL connector, by simultane-
ously inputting PLAY and RECORD signals while this unit is
stopped, you can start recording immediately. In addition,
by simultaneously inputting PLAY and RECORD signals
during playback in timeline mode, you can start overwriting
the recording.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-4000 in the language / languages: English as an attachment in your email.

The manual is 10,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info