617903
13
Zoom out
Zoom in
Previous page
1/152
Next page
TASCAM HS-4000
13
2 − Names and functions of parts
Rear panel
h ANALOG LINE IN 1–4 connectors
These XLR connectors are balanced analog line inputs.
(1:GND, 2:HOT, 3:COLD)
j DIGITAL LINE IN 1–2 connectors
Use these balanced XLR connectors (1 and 2) for digital
audio input in AES3-2003/IEC60958-4 (AES/EBU) or
IEC60958-3 (S/PDIF) format.
Sampling frequencies of 88.2 and 96 kHz are transmitted at
double speed.
The built-in sampling rate converter can handle 32–192 kHz.
k MONITOR ANALOG OUT L/R connectors
These are left and right balanced analog XLR monitoring
output connectors (1: GND, 2: HOT, 3: COLD).
These output monitoring signals (the audio output from the
internal monitoring mixer).
l RS-232C connector
This is a D-sub 9-pin RS-232C serial control connector.
Use it to connect an external controller.
NOTE
The RS-232C connector will be made functional in a future
firmware version update.
It cannot be used at the same time as the RS-422 connector.
(See “RS–232C page” on page 108.)
; PARALLEL connector
Connect an external controller, for example, to this 25-pin
D-sub parallel control connector.
z AC IN connector
Connect the included power cord here.
x ANALOG LINE OUT 1–4 connectors
These XLR connectors are balanced analog line outputs.
(1:GND, 2:HOT, 3:COLD)
In dual playlist mode, player A outputs from connectors 1
and 2, while player B outputs from connectors 3 and 4.
c DIGITAL LINE OUT 1/2 connectors
These XLR connectors are balanced outputs for digital audio
in AES3-2003/IEC 60958-4 (AES/EBU) format.
Sampling frequencies of 88.2 and 96 kHz are transmitted at
double speed.
In dual playlist mode, player A outputs from connector 1,
while player B outputs from connector 2.
v REMOTE connectors
Connect a TASCAM RC-HS32PD remote control (sold
separately) here.
CAUTION
This is not an Ethernet connector (LAN, etc.). Never connect
this to a network using an Ethernet cable.
Doing so could damage this unit or equipment in the
network.
b RS-422 connector
This is a D-sub 9-pin RS-422 serial control connector.
Use it to connect an external controller, for example.
NOTE
It cannot be used at the same time as the RS-232C
connector. (See “RS–422 page” on page 108.)
n TIMECODE IN connector
This XLR connector is a balanced input for SMPTE timecode
input.
m TIMECODE OUT connector
This XLR connector is a balanced output for SMPTE timecode
output.
, WORD/VIDEO IN connector
This is a BNC-type word clock an video reference signal
input connector. Use it to input a word clock signal (44.1kHz,
48kHz, 48kHz pull-down, 48kHz pull-up, 88.2kHz or 96kHz)
or a video reference signal (NTSC/PAL black burst signal,
HDTV Tri-level signal).
Use the switch to set whether or not to terminate with 75Ω.
. WORD/VIDEO THRU/WORD OUT connector
This is a BNC-type word clock (through/output) and video
reference signal through/output connector.
Use it to output a word clock signal (through, 44.1kHz,
48kHz, 48kHz pull-down, 48kHz pull-up, 88.2kHz or 96kHz
output) or a video reference signal (IN connector signal
through).
Use the THRU/WORD OUT switch to set the signal output.
/ 75Ω OFF/ON and THRU/WORD OUT switch
Use this switch to make the following settings.
o Whether or not the WORD/VIDEO IN connector has
termination resistance (75Ω)
o The WORD/VIDEO output THRU/OUT setting (OUT is
only for WORD)
! ETHERNET connector
Use this Ethernet connector for network connection to
conduct file transfer and external control of this device.
@ GROUND terminal
When using a TASCAM RC-HS32PD remote control (sold
separately), depending on the operating environment, the
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-4000 in the language / languages: English as an attachment in your email.

The manual is 10,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info