617904
13
Zoom out
Zoom in
Previous page
1/156
Next page
TASCAM HS-2000
13
2 − Names and functions of parts
Rear panel
hANALOG IN [LINE] connectors (L/R)
These are balanced analog XLR connectors for line
input.(1: GND, 2: HOT, 3: COLD)
jDIGITAL IN [LINE] connector
This balanced XLR connector is for digital audio input
in AES3-2003/IEC60958-4 (AES/EBU) or IEC60958-3 (S/
PDIF) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
The built-in sampling rate converter can handle 32–
192 kHz.
kANALOG OUT [MONITOR] connectors (L/R)
These balanced analog XLR connectors output the left
and right monitoring signals. (1: GND, 2: HOT, 3: COLD)
lRS-232C connector
Connect an external controller, for example, to this
9-pin
D-sub connector for RS-232C serial control.
NOTE
It cannot be used at the same time as the RS-422
connector. (See “RS-232C page” on page 107.)
;PARALLEL connector
Connect a TASCAM RC-SS20 or other external
controller to this 25-pin D-sub parallel control
connector.
zAC IN connector
Connect the included power cord here.
xANALOG OUT [LINE] connectors (L/R)
These balanced analog XLR connectors are for line
output. (1: GND, 2: HOT, 3: COLD)
cDIGITAL OUT [LINE] connector
This balanced XLR connector is for digital audio output
in AES3-2003/IEC 60958-4 (AES/EBU) format.
Sampling frequencies of 88.2 and 96 kHz are
transmitted at double speed. Sampling frequencies of
176.4 and 192 kHz are transmitted at quadruple speed.
vREMOTE connector
Connect a TASCAM RC-HS32PD or RC-HS20PD remote
control (sold separately) here.
CAUTION
Never connect this to a network using an Ethernet cable.
Doing so could damage this unit or network equipment.
bRS-422 connector
Connect an external controller, for example, to this
9-pin D-sub connector for RS-422 serial control.
NOTE
It cannot be used at the same time as the RS-232C
connector. (See “RS-422 page” on page 108.)
nTIMECODE INPUT connector
This balanced XLR connector is for SMPTE timecode
input.
mTIMECODE OUTPUT connector
This balanced XLR connector is for SMPTE timecode
output.
,WORD/VIDEO IN connector
This BNC-type connector accepts a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz) or a video reference
signal (NTSC/PAL black burst signal, HDTV Tri-Level
signal).
Use the switch to turn the integral 75Ω terminator on
or off.
.WORD/VIDEO THRU/OUT connector [cut WORD”]
This BNC-type connector outputs a word clock signal
(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,
88.2kHz, 96kHz, 176.4kHz, 192kHz or thru) or a video
reference signal (IN connector signal thru only).
Use the THRU/WORD OUT switch to set the signal
output.
/75Ω ON/OFF/THRU/WORD OUT switch
Use this three-way switch to make one of the following
settings.
Terminator OFF and WORD/VIDEO THRU
Terminator OFF and WORD OUT (no VIDEO OUT)
Terminator ON and WORD OUT (no VIDEO OUT)
!ETHERNET connector
Use this Ethernet connector to connect the unit with
a network for file transfer and to control this unit from
another device on the network.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-2000 in the language / languages: English as an attachment in your email.

The manual is 12,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info