617907
67
Zoom out
Zoom in
Previous page
1/132
Next page
TASCAM HS-2 67
NOTE
To load a take from the current session, instead of steps
1–4 above, touch the session name button at the top right
of the project screen or touch the take name button on
the Home Screen, and touch the
TAKE List
button in
the pull-down menu to open the take selection screen for
the current session.
4 Select the take that you want to load.
5 Touch the
MENU
button in the take selection screen
to open the pull-up menu.
6 Touch the
LOAD
button in the pull-up menu.
7 When a confirmation message appears in the pop-
up window, touch the
OK
button or press the DATA
dial.
When loading completes, the Home Screen opens.
NOTE
You can also press the e button for a take to load it.
In this case, no pop-up window appears, and the take
selection screen remains open after loading (the Home
screen does not reopen.)
Setting input monitoring
Turn input monitoring OFF when playing back. If input
monitoring is ON, sound from the input connectors will
be output through all output connectors of this unit.
1 Touch the
INPUT MONITOR
button on the Home
Screen to open a pull-up with the input monitoring
ON/OFF buttons.
2 If input monitoring is on (
ON
button appears blue),
touch the
OFF
button to turn it off (
OFF
button ap-
pears blue).
Playback control
Press the PLAY key to start playback.
Press the PAUSE key to pause playback.
Press the PLAY key again to resume playback.
Press the STOP (RETAKE) key to stop playback.
Press the . [MARK .] key or // [MARK /] key
to switch takes.
Press and hold the m [ ] or , [ ] key to
search backward or forward.
Press the . [MARK .] or / [MARK /] key while
pressing and holding the SHIFT key to move between
marks.
Press and hold the m [ ] key or , [ ] key
while pressing and holding the SHIFT key to search at
high-speed.
NOTE
On the
PLAY SETUP
screen, you can set whether only
the currently selected take is played or whether all the
takes within the current session are played. You can
also enable and disable repeat playback. (See “Playback
settings (PLAY SETUP)” on page 91.)
Playback functions can also be used through parallel
control.
Using the call function
Press the CALL (CHASE) key to locate to the point where
playback was last started from playback standby (call
point) and put the unit in playback standby mode.
Using the flash start function in take mode
Using a TASCAM RC-HS20PD (sold separately) or other
remote controller, flash start playback is possible.
For details, see “Flash start function on page 113.
Take operations
Some takes will be made under session folders. For details
on operations for project and session, see “5–Projects” on
page 36.
The following functions are used for take operations:
Editing the start time of a take
Exporting a take
Deleting a take
Sorting a take
Moving the order of alignment of a take
Editing the name of a take
Dividing a take (Divide)
Combining takes (Combine)
Undoing the previous edit (UNDO)
Redoing the cancelled edit (REDO)
8–Take mode
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-2 in the language / languages: English as an attachment in your email.

The manual is 4,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info